X25320PI datasheet(8/15 Pages) XICOR

8 / 15 page

X25320

Notes:

(1) VIL min. and VIH max. are for reference only and are not tested.

(2) This parameter is periodically sampled and not 100% tested.

(3) tPUR and tPUW are the delays required from the time VCC is stable until the specified operation can be initiated. These parameters

are periodically sampled and not 100% tested.

*COMMENT

Stresses above those listed under “Absolute Maximum

Ratings” may cause permanent damage to the device.

This is a stress rating only and the functional operation of

the device at these or any other conditions above those

listed in the operational sections of this specification is

not implied. Exposure to absolute maximum rating con-

ditions for extended periods may affect device reliability.

ABSOLUTE MAXIMUM RATINGS*

Temperature under Bias .................. –65

°C to +135°C

Storage Temperature ....................... –65

°C to +150°C

Voltage on any Pin with Respect to VSS ......... –1V to +7V

D.C. Output Current ............................................. 5mA

Lead Temperature

(Soldering, 10 seconds) .............................. 300

°C

POWER-UP TIMING

Symbol

Parameter

Min.

Max.

Units

tPUR(3)

Power-up to Read Operation

tPUW(3)

Power-up to Write Operation

3063 PGM T09

RECOMMENDED OPERATING CONDITIONS

Temp

Min.

Max.

Commercial

°C

+70

°C

Industrial

–40

°C

+85

°C

Military

–55

°C

+125

°C

3063 PGM T06.1

Supply Voltage

Limits

X25320

±10%

X25320-2.7

2.7V to 5.5V

3063 PGM T07.1

D.C. OPERATING CHARACTERISTICS (Over the recommended operating conditions unless otherwise specified.)

Limits

Symbol

Parameter

Min.

Max.

Units

Test Conditions

ICC

VCC Supply Current (Active)

SCK = VCC x 0.1/VCC x 0.9 @ 2MHz,

SO = Open,

CS = VSS

ISB

VCC Supply Current (Standby)

µA

CS = VCC, VIN = VSS or VCC

ILI

Input Leakage Current

µAVIN = VSS to VCC

ILO

Output Leakage Current

µAVOUT = VSS to VCC

VIL(1)

Input LOW Voltage

–1

VCC x 0.3

VIH(1)

Input HIGH Voltage

VCC x 0.7 VCC + 0.5

VOL1

Output LOW Voltage

0.4

VCC = 5V, IOL = 3mA

VOH1

Output HIGH Voltage

VCC – 0.8

VCC = 5V, IOH = -1.6mA

VOL2

Output LOW Voltage

0.4

VCC = 3V, IOL = 1.5mA

VOH2

Output HIGH Voltage

VCC – 0.3

VCC = 3V, IOH = -0.4mA

3063 PGM T08.3

CAPACITANCE TA = +25°C, f = 1MHz, VCC = 5V.

Symbol

Test

Max.

Units

Conditions

COUT(2)

Output Capacitance (SO)

VOUT = 0V

CIN(2)

Input Capacitance (SCK, SI,

CS, WP, HOLD)6

VIN = 0V

3063 PGM T10.1

X25320PI bảng dữ liệu(PDF) 8 Page - Xicor Inc.

X25320PI bảng dữ liệu(HTML) 8 Page - Xicor Inc.

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

bảng dữ liệu tải về

Link URL