| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
ATmega165 bảng dữ liệu(PDF) 256 Page - ATMEL Corporation |
|
|
|||||||||||||||||||||||||||||
ATmega165 bảng dữ liệu(HTML) 256 Page - ATMEL Corporation |
|
256 / 336 page ![]() 256 ATmega165/V 2573G–AVR–07/09 Programming the Fuse Low Bits The algorithm for programming the Fuse Low bits is as follows (refer to “Programming the Flash” on page 252 for details on Command and Data loading): 1. A: Load Command “0100 0000”. 2. C: Load Data Byte. Bit n = “0” programs and bit n = “1” erases the Fuse bit. 3. Give WR a negative pulse and wait for RDY/BSY to go high. Programming the Fuse High Bits The algorithm for programming the Fuse High bits is as follows (refer to “Programming the Flash” on page 252 for details on Command and Data loading): 1. A: Load Command “0100 0000”. 2. C: Load Data Byte. Bit n = “0” programs and bit n = “1” erases the Fuse bit. 3. Set BS1 to “1” and BS2 to “0”. This selects high fuse byte. 4. Give WR a negative pulse and wait for RDY/BSY to go high. 5. Set BS1 to “0”. This selects low data byte. Programming the Extended Fuse Bits The algorithm for programming the Extended Fuse bits is as follows (refer to “Program- ming the Flash” on page 252 for details on Command and Data loading): 1. 1. A: Load Command “0100 0000”. 2. 2. C: Load Data Byte. Bit n = “0” programs and bit n = “1” erases the Fuse bit. 3. 3. Set BS1 to “0” and BS2 to “1”. This selects extended fuse byte. 4. 4. Give WR a negative pulse and wait for RDY/BSY to go high. 5. 5. Set BS2 to “0”. This selects low data byte. Figure 115. Programming the FUSES Waveforms Programming the Lock Bits The algorithm for programming the Lock bits is as follows (refer to “Programming the Flash” on page 252 for details on Command and Data loading): 1. A: Load Command “0010 0000”. 2. C: Load Data Low Byte. Bit n = “0” programs the Lock bit. If LB mode 3 is pro- grammed (LB1 and LB2 is programmed), it is not possible to program the Boot Lock bits by any External Programming mode. 3. Give WR a negative pulse and wait for RDY/BSY to go high. The Lock bits can only be cleared by executing Chip Erase. RDY/BSY WR OE RESET +12V PAGEL 0x40 DATA DATA XX XA1 XA0 BS1 XTAL1 AC 0x40 DATA XX AC Write Fuse Low byte Write Fuse high byte 0x40 DATA XX AC Write Extended Fuse byte BS2 |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |