CS43L22 datasheet(34/68 Pages) CIRRUS

34 / 68 page

DS792F1

CS43L22

Confidential Draft

10/7/08

5. CONTROL PORT OPERATION

The control port is used to access the registers allowing the CS43L22 to be configured for the desired op-

erational modes and formats. The operation of the control port may be completely asynchronous with re-

spect to the audio sample rates. However, to avoid potential interference problems, the control port pins

should remain static if no operation is required.

The control port operates using an I²C interface with the CS43L22 acting as a slave device.

5.0.1

I²C Control

SDA is a bidirectional data line. Data is clocked into and out of the part by the clock, SCL. The signal tim-

ings for a read and write cycle are shown in Figure 16 and Figure 17. A Start condition is defined as a

falling transition of SDA while the clock is high. A Stop condition is defined as a rising transition of SDA

while the clock is high. All other transitions of SDA occur while the clock is low. The first byte sent to the

CS43L22 after a Start condition consists of a 7-bit chip address field and a R/W bit (high for a read, low

for a write).

The upper 7 bits of the address field are fixed at 1001010. To communicate with the CS43L22, the chip

address field, which is the first byte sent to the CS43L22, should match 1001010. The eighth bit of the

address is the R/W bit. If the operation is a write, the next byte is the Memory Address Pointer (MAP),

which selects the register to be read or written. If the operation is a read, the contents of the register point-

ed to by the MAP will be output. Setting the auto-increment bit in MAP allows successive reads or writes

of consecutive registers. Each byte is separated by an acknowledge bit. The ACK bit is output from the

CS43L22 after each input byte is read and is input to the CS43L22 from the microcontroller after each

transmitted byte.

Since the read operation cannot set the MAP, an aborted write operation is used as a preamble. As shown

in Figure 17, the write operation is aborted after the acknowledge for the MAP byte by sending a stop con-

dition. The following pseudocode illustrates an aborted write operation followed by a read operation.

Send start condition.

Send 10010100 (chip address & write operation).

Receive acknowledge bit.

24 25

SCL

CHIP ADDRESS (WRITE)

MAP BYTE

DATA

DATA +1

START

ACK

STOP

ACK

SDA

INCR

16 17 18

10 11

13 14 15

27 28

DATA +n

Figure 16. Control Port Timing, I²C Write

SCL

CHIP ADDRESS (WRITE)

MAP BYTE

DATA

DATA +1

START

ACK

STOP

ACK

0 1 0 0

SDA

1 0 1

CHIP ADDRESS (READ)

START

INCR

12 13 14 15

20 21 22 23 24

26 27 28

10 11

17 18

ACK

DATA + n

STOP

Figure 17. Control Port Timing, I²C Read

CS43L22 bảng dữ liệu(PDF) 34 Page - Cirrus Logic

CS43L22 bảng dữ liệu(HTML) 34 Page - Cirrus Logic

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68

bảng dữ liệu tải về

Link URL