| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
M16C/62M bảng dữ liệu(PDF) 133 Page - Renesas Technology Corp |
|
|
|||||||||||||||||||||||||||||
M16C/62M bảng dữ liệu(HTML) 133 Page - Renesas Technology Corp |
|
133 / 615 page ![]() Mitsubishi microcomputers M16C / 62A Group SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER Serial I/O 1-114 UARTi transmit/receive control register 0 Symbol Address When reset UiC0(i=0,1) 03A416, 03AC16 0816 b7 b6 b5 b4 b3 b2 b1 b0 Function (During UART mode) W R Function (During clock synchronous serial I/O mode) TXEPT CLK1 CLK0 CRS CRD NCH CKPOL BRG count source select bit Transmit register empty flag 0 : Transmit data is output at falling edge of transfer clock and receive data is input at rising edge 1 : Transmit data is output at rising edge of transfer clock and receive data is input at falling edge CLK polarity select bit CTS/RTS function select bit CTS/RTS disable bit Data output select bit 0 0 : f1 is selected 0 1 : f8 is selected 1 0 : f32 is selected 1 1 : Must not be set. b1 b0 0 : LSB first 1 : MSB first 0 : Data present in transmit register (during transmission) 1 : No data present in transmit register (transmission completed) 0 : CTS/RTS function enabled 1 : CTS/RTS function disabled (P60 and P64 function as programmable I/O port) 0 : TXDi pin is CMOS output 1 : TXDi pin is N-channel open-drain output UFORM Transfer format select bit 0 0 : f1 is selected 0 1 : f8 is selected 1 0 : f32 is selected 1 1 : Must not be set. b1 b0 Valid when bit 4 = “0” 0 : CTS function is selected (Note 1) 1 : RTS function is selected (Note 2) Valid when bit 4 = “0” 0 : CTS function is selected (Note 1) 1 : RTS function is selected (Note 2) 0 : Data present in transmit register (during transmission) 1 : No data present in transmit register (transmission completed) 0: TXDi pin is CMOS output 1: TXDi pin is N-channel open-drain output Must always be “0” Bit name Bit symbol Must always be “0” Note 1: Set the corresponding port direction register to “0”. Note 2: The settings of the corresponding port register and port direction register are invalid. 0 : CTS/RTS function enabled 1 : CTS/RTS function disabled (P60 and P64 function as programmable I/O port) UART2 transmit/receive control register 0 Symbol Address When reset U2C0 037C16 0816 b7 b6 b5 b4 b3 b2 b1 b0 Function (During UART mode) W R Function (During clock synchronous serial I/O mode) TXEPT CLK1 CLK0 CRS CRD CKPOL BRG count source select bit Transmit register empty flag 0 : Transmit data is output at falling edge of transfer clock and receive data is input at rising edge 1 : Transmit data is output at rising edge of transfer clock and receive data is input at falling edge CLK polarity select bit CTS/RTS function select bit CTS/RTS disable bit 0 0 : f1 is selected 0 1 : f8 is selected 1 0 : f32 is selected 1 1 : Must not be set. b1 b0 0 : LSB first 1 : MSB first 0 : Data present in transmit register (during transmission) 1 : No data present in transmit register (transmission completed) 0 : CTS/RTS function enabled 1 : CTS/RTS function disabled (P73 functions programmable I/O port) 0 : TXDi pin is CMOS output 1 : TXDi pin is N-channel open-drain output UFORM Transfer format select bit (Note 3) 0 0 : f1 is selected 0 1 : f8 is selected 1 0 : f32 is selected 1 1 : Must not be set. b1 b0 Valid when bit 4 = “0” 0 : CTS function is selected (Note 1) 1 : RTS function is selected (Note 2) Valid when bit 4 = “0” 0 : CTS function is selected (Note 1) 1 : RTS function is selected (Note 2) 0 : Data present in transmit register (during transmission) 1 : No data present in transmit register (transmission completed) 0: TXDi pin is CMOS output 1: TXDi pin is N-channel open-drain output Must always be “0” Bit name Bit symbol Note 1: Set the corresponding port direction register to “0”. Note 2: The settings of the corresponding port register and port direction register are invalid. Note 3: Only clock synchronous serial I/O mode and 8-bit UART mode are valid. 0 : CTS/RTS function enabled 1 : CTS/RTS function disabled (P73 functions programmable I/O port) Nothing is assigned. In an attempt to write to this bit, write “0”. The value, if read, turns out to be “0”. 0 : LSB first 1 : MSB first Figure 1.16.6. Serial I/O-related registers (3) |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |