| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
H8S/2114R bảng dữ liệu(PDF) 148 Page - Renesas Technology Corp |
|
|
|||||||||||||||||||||||||||||
H8S/2114R bảng dữ liệu(HTML) 148 Page - Renesas Technology Corp |
|
148 / 1038 page ![]() Section 5 Interrupt Controller Rev. 3.00 Jul. 14, 2005 Page 100 of 986 REJ09B0098-0300 IRQnE IRQnF S R Q IRQn ISSm ExIRQn IRQn interrupt request Clear signal IRQnSCA, IRQnSCB n = 15 to 0 m = 15 to 7 and 5 to 0 Note: Switching between the IRQ6 and ExIRQ6 pins is controlled by the EIVS bit in SYSCR3. Edge/level detection circuit Figure 5.4 Block Diagram of Interrupts IRQ15 to IRQ0 (3) KIN15 to KIN0 Interrupts and WUE15 to WUE0 Interrupts Interrupts KIN15 to KIN0 and WUE15 to WUE0 are requested by an input signal at pins KIN15 to KIN0 and WUE15 to WUE0. Interrupts KIN15 to KIN0 and WUE15 to WUE0 have the following features according to the setting of the EIVS bit in system control register 3 (SYSCR3). • H8S/2140B Group compatible vector mode (EIVS = 0 in SYSCR3) Interrupts WUE7 to WUE0 and KIN15 to KIN8 correspond to interrupt IRQ7, and interrupts KIN7 to KIN0 correspond to interrupt IRQ6. The pin conditions for generating an interrupt request, whether the interrupt request is enabled, interrupt control level setting, and status of the interrupt request for the above interrupts are in accordance with the settings and status of the relevant interrupts IRQ7 and IRQ6. Interrupt settings for interrupts WUE15 to WUE8 can be made regardless of the settings for interrupts IRQ7 and IRQ6. Enabling or disabling of interrupt requests KIN15 to KIN0 and WUE15 to WUE0 can be selected using KMIMRA, KMIMR, WUEMRB, and WUEMR. If the KIN7 to KIN0 pins or WUE15 to WUE8 pins, and WUE7 to WUE0 pins are specified to be used as key-sensing interrupt input pins and wake-up event interrupt input pins, the interrupt sensing condition for the corresponding interrupt source (IRQ6 or IRQ7) must be set to low-level sensing or falling-edge sensing. When using the IRQ6 pin as the IRQ6 interrupt input pin, the KMIMR6 bit must be cleared to 0. When using the IRQ7 pin as the IRQ7 interrupt input pin, the KMIMR15 to KMIMR8 and WUEMR7 to WUEMR0 bits must all be set to 1. If even one of these bits is cleared to 0, the IRQ7 interrupt input from the IRQ7 pin is ignored. |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |