| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
H8S/2114R bảng dữ liệu(PDF) 147 Page - Renesas Technology Corp |
|
|
|||||||||||||||||||||||||||||
H8S/2114R bảng dữ liệu(HTML) 147 Page - Renesas Technology Corp |
|
147 / 1038 page ![]() Section 5 Interrupt Controller Rev. 3.00 Jul. 14, 2005 Page 99 of 986 REJ09B0098-0300 5.4 Interrupt Sources 5.4.1 External Interrupt Sources The interrupt sources of external interrupts are NMI, IRQ15 to IRQ0, KIN15 to KIN0 and WUE15 to WUE0. These interrupts can be used to restore this LSI from software standby mode. (1) NMI Interrupt The nonmaskable external interrupt NMI is the highest-priority interrupt, and is always accepted regardless of the interrupt control mode or the status of the CPU interrupt mask bits. The NMIEG bit in SYSCR can be used to select whether an interrupt is requested at a rising edge or falling edge on the NMI pin. (2) IRQ15 to IRQ0 Interrupts Interrupts IRQ15 to IRQ0 are requested by an input signal at pins IRQ15 to IRQ0 or pins ExIRQ15 to ExIRQ0. Interrupts IRQ15 to IRQ0 have the following features: • The interrupt exception handling for interrupt requests IRQ15 to IRQ0 can be started at an independent vector address. • Using ISCR, it is possible to select whether an interrupt is generated by a low level, falling edge, rising edge, or both edges, at pins IRQ15 to IRQ0 or pins ExIRQ15 to ExIRQ0. • Enabling or disabling of interrupt requests IRQ15 to IRQ0 can be selected with IER. • The status of interrupt requests IRQ15 to IRQ0 is indicated in ISR. ISR flags can be cleared to 0 by software. When the interrupts are requested while IRQ15 to IRQ0 interrupt requests are generated at low level of IRQn input, hold the corresponding IRQ input at low level until the interrupt handling starts. Then put the relevant IRQ input back to high level within the interrupt handling routine and clear the IRQnF bit (n = 15 to 0) in ISR to 0. If the relevant IRQ input is put back to high level before the interrupt handling starts, the relevant interrupt may not be executed. The detection of IRQ15 to IRQ0 interrupts does not depend on whether the relevant pin has been set for input or output. Therefore, when a pin is used as an external interrupt input pin, clear the DDR bit of the corresponding port to 0 so it is not used as an I/O pin for another function. A block diagram of interrupts IRQ15 to IRQ0 is shown in figure 5.4. |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |