R8C datasheet(197/199 Pages) RENESAS

197 / 199 page

C-7

REVISION HISTORY

Rev.

Date

Description

Page

Summary

R8C/10 Group Hardware Manual

1.20 Jan.27.2006

113

14.7 Output Impedance of Sensor under A/D Conversion added

116

Figure 15.1 Programmable I/O Ports (1); NOTES: 1 added

117

Figure 15.2 Programmable I/O Ports (2); NOTES: 1 added

118

Figure 15.3 Programmable I/O Ports (3); NOTES: 1 added

119

Figure 15.4 Programmable I/O Ports (4); NOTES: 3 added

127

_______

Table 15.20 Port P33/INT3/TCIN Setting; Bit: “PD3_1”

→ “PD3_3”

_______

Table 15.22 Port P45/INT0 Setting; Bit: “PD3_3”

→ “PD4_5”

Table 15.23 Port XIN/P46, XOUT/P47 Setting;

Setting value: External input to XIN pin, “H” output from XOUT pin;

CM1: “1”

→ “0”, CM0: “0” → “1”, Feedback resistance: “OFF” → “ON”

129

Table 16.2 Recommended Operating Conditions; NOTES: 1, 2, 3 revised

130

Table 16.3 A/D Conversion Characteristics;

“A/D operation clock frequency”

→ “A/D operating clock frequency” revised

NOTES: 1, 2, 3, 4 revised

Table 16.4 Flash Memory (Program ROM) Electrical Characteristics;

“Data retention duration”

→ “Data hold time” revised

“Topr”

→ “Ambient temperature” revised

NOTES: 2 added

Measuring condition of byte program time and block erase time deleted

132

Table 16.6 Electrical Characteristics (1) [VCC=5V];

“P10 to P17 Except XOUT”

→ “Except P10 to P17, XOUT” revised

133

Table 16.7 Electrical Characteristics (2) [VCC=5V]

NOTES: 1, 2 revised

Measuring condition: Stop mode “Topr = 25 °C” added

136

Table 16.13 Electrical Characteristics (3) [VCC=3V]

“P10 to P17 Except XOUT”

→ “Except P10 to P17, XOUT” revised

137

Table 16.14 Electrical Characteristics (4) [VCC=3V]

NOTES: 1, 2 revised

Measuring condition: Stop mode “Topr = 25 °C” added

147

Figure 17.4 FMR1 and FMR4;

Flash memory control register 4 NOTES: 2 “Other than this period, this bit is set to

“0”.” revised

153

Figure 17.11 Block Erase Command (When Using Erase-suspend Function);

“Write ‘D016’ to the uppermost block address”

→

“Write ‘D016’ to the any block address” revised

156

Figure 17.12 Full Status Check and Handling Procedure for Each Error revised

158

Table 17.7 Pin Functions (Flash Memory Standard Serial I/O Mode);

____________

RESET: revised

162

19.1.1 Stop Mode

“Use the next program to enter stop mode.” added

“• Example of entering stop mode”

→ “• Program of entering stop mode”

“Program Example” deleted

166

19.3.1 Oscillation Stop Detection Function

“Since the oscillation stop ... is 2 MHz or below, ...”

→

“Since the oscillation stop ... is below 2 MHz, ...” revised

176

Appendix figure 2.2 Connecting examples with M16C Flash Starter (M3A-0806);

Pulled up added

NOTES: 1 revised

R8C bảng dữ liệu(PDF) 197 Page - Renesas Technology Corp

R8C bảng dữ liệu(HTML) 197 Page - Renesas Technology Corp

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL