TMS320DM643 datasheet(152/162 Pages) TI

152 / 162 page

www.ti.com

5.19 JTAG

5.19.1

JTAG Device-Specific Information

TMS320DM643

Video/Imaging Fixed-Point Digital Signal Processor

SPRS269C – FEBRUARY 2005 – REVISED JANUARY 2007

The JTAG interface is used for BSDL testing and emulation of the DM643 device.

Note: IEEE Standard 1149.1-1990 Standard-Test-Access Port and Boundary Scan Architecture.

5.19.1.1

IEEE 1149.1 JTAG Compatibility Statement

The TMS320DM643 DSP requires that both TRST and RESET be asserted upon power up to be properly

initialized. While RESET initializes the DSP core, TRST initializes the DSP's emulation logic. Both resets

are required for proper operation.

Note: TRST is synchronous and must be clocked by TCLK; otherwise, BSCAN may not respond as

expected after TRST is asserted.

While both TRST and RESET need to be asserted upon power up, only RESET needs to be released for

the DSP to boot properly. TRST may be asserted indefinitely for normal operation, keeping the JTAG port

interface and DSP's emulation logic in the reset state. TRST only needs to be released when it is

necessary to use a JTAG controller to debug the DSP or exercise the DSP's boundary scan functionality.

RESET must be released only in order for boundary-scan JTAG to read the variant field of IDCODE

correctly. Other boundary-scan instructions work correctly independent of current state of RESET.

The TMS320DM643 DSP includes an internal pulldown (IPD) on the TRST pin to ensure that TRST will

always be asserted upon power up and the DSP's internal emulation logic will always be properly

initialized when this pin is not routed out. JTAG controllers from Texas Instruments actively drive TRST

high. However, some third-party JTAG controllers may not drive TRST high but expect the use of a pullup

resistor on TRST. When using this type of JTAG controller, assert TRST to intialize the DSP after powerup

and externally drive TRST high before attempting any emulation or boundary scan operations.

Following the release of RESET, the low-to-high transition of TRST must be "seen" to latch the state of

EMU1 and EMU0. The EMU[1:0] pins configure the device for either Boundary Scan mode or Emulation

mode. For more detailed information, see the terminal functions section of this data sheet.

Note: The DESIGN_WARNING section of the TMS320DM643 BSDL file contains information and

constraints regarding proper device operation while in Boundary Scan Mode.

5.19.1.2

JTAG ID Register Description

The JTAG ID register is a read-only register that identifies to the customer the JTAG/Device ID. For the

DM643 device, the JTAG ID register resides at address location 0x01B3 F008. The register hex value for

the DM643 device is: 0x0007 902F. For the actual register bit names and their associated bit field

descriptions, see Figure 5-69 and Table 5-79.

31-28

27-12

11-1

VARIANT (4-Bit)

PART NUMBER (16-Bit)

MANUFACTURER (11-Bit)

LSB

R-0000

R-0000 0000 0111 1001

R-0000 0010 111

R-1

Legend: R = Read only, -n = value after reset

Figure 5-69. JTAG ID Register Description – TMS320DM643 Register Value – 0x0007 902F

DM643 Peripheral Information and Electrical Specifications

152

Submit Documentation Feedback

TMS320DM643 bảng dữ liệu(PDF) 152 Page - Texas Instruments

TMS320DM643 bảng dữ liệu(HTML) 152 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL