M25P10-AVMB3TPSLASHY datasheet(22/51 Pages) NUMONYX

22 / 51 page

Instructions

M25P10-A

22/51

6.5

Write Status Register (WRSR)

The Write Status Register (WRSR) instruction allows new values to be written to the Status

have been executed. After the Write Enable (WREN) instruction has been decoded and

executed, the device sets the Write Enable Latch (WEL).

The Write Status Register (WRSR) instruction is entered by driving Chip Select (S) Low,

followed by the instruction code and the data byte on Serial Data input (D).

The instruction sequence is shown in Figure 11.

The Write Status Register (WRSR) instruction has no effect on b6, b5, b4, b1 and b0 of the

Status Register. b6, b5 and b4 are always read as 0.

Chip Select (S) must be driven High after the eighth bit of the data byte has been latched in.

If not, the Write Status Register (WRSR) instruction is not executed. As soon as Chip Select

(S) is driven High, the self-timed Write Status Register cycle (whose duration is tW) is

initiated. While the Write Status Register cycle is in progress, the Status Register may still

be read to check the value of the Write In Progress (WIP) bit. The Write In Progress (WIP)

bit is 1 during the self-timed Write Status Register cycle, and is 0 when it is completed. At

some unspecified time before the cycle is completed, the Write Enable Latch (WEL) is reset.

The Write Status Register (WRSR) instruction allows the user to change the values of the

Block Protect (BP1, BP0) bits, to define the size of the area that is to be treated as read-

only, as defined in Table 2. The Write Status Register (WRSR) instruction also allows the

user to set or reset the Status Register Write Disable (SRWD) bit in accordance with the

Write Protect (W) signal. The Status Register Write Disable (SRWD) bit and Write Protect

(W) signal allow the device to be put in the Hardware Protected mode (HPM). The Write

Status Register (WRSR) instruction is not executed once the Hardware Protected mode

(HPM) is entered.

The protection features of the device are summarized in Table 7.

When the Status Register Write Disable (SRWD) bit of the Status Register is 0 (its initial

delivery state), it is possible to write to the Status Register provided that the Write Enable

Latch (WEL) bit has previously been set by a Write Enable (WREN) instruction, regardless

of the whether Write Protect (W) is driven High or Low.

When the Status Register Write Disable (SRWD) bit of the Status Register is set to ‘1’, two

cases need to be considered, depending on the state of Write Protect (W):

●

If Write Protect (W) is driven High, it is possible to write to the Status Register provided

that the Write Enable Latch (WEL) bit has previously been set by a Write Enable

(WREN) instruction

●

If Write Protect (W) is driven Low, it is not possible to write to the Status Register even

if the Write Enable Latch (WEL) bit has previously been set by a Write Enable (WREN)

instruction. (Attempts to write to the Status Register are rejected, and are not accepted

for execution). As a consequence, all the data bytes in the memory area that are

software protected (SPM) by the Block Protect (BP1, BP0) bits of the Status Register,

are also hardware protected against data modification.

M25P10-AVMB3TP/Y bảng dữ liệu(PDF) 22 Page - Numonyx B.V

M25P10-AVMB3TP/Y bảng dữ liệu(HTML) 22 Page - Numonyx B.V

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51

bảng dữ liệu tải về

Link URL