| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
2EDF7175F bảng dữ liệu(PDF) 9 Page - Infineon Technologies AG |
|
|
|||||||||||||||||||||||||||||
2EDF7175F bảng dữ liệu(HTML) 9 Page - Infineon Technologies AG |
|
9 / 37 page ![]() Final datasheet 9 Rev.2.9 2024-05-16 EiceDRIVER™ 2EDi product family 2EDSx reinforced, 2EDFx functional isolated 4A/8A, 1A/2A gate drivers Functional description 3.2.1 Typical applications by isolation type Isolated gate drivers are typically deployed in the following applications. 3.3 Supply voltages Three different power domains with independent internal power management are utilized to supply the input chip and the two output drivers. An undervoltage lockout functionality (UVLO) in each domain enables a defined startup and ensures a robust operation under all conditions. 3.3.1 Input-side power supply The input side is powered via VDDI with nominal 3.3 V. For using the device with a supply voltage > 3.5 V the on- chip switched low-dropout regulator (SLDO) must be activated and an external shunt resistor RVDDI has to be connected to VDDI. It is recommended to use a ceramic bypass capacitor (10 nF - 22 nF) between VDDI and GNDI. The SLDO is activated if the pin SLDON is connected to GNDI. A hard-wired connection is recommended. The SLDO regulates the current through an external resistor RVDDI connected between the external supply voltage VDD and pin VDDI as depicted in Figure 1 to generate the required voltage drop. For proper operation it has to be ensured that the current through RVDDI always exceeds the maximum supply current IVDD of the input chip (see Figure 7). Thus, RVDDI has to fulfill: RVDDI < (VDD -3.3)/ IVDD,max A typical choice for VDD = 12 V is RVDDI = 3 kΩ, resulting in sufficient margin between resistor current and VDDI operating current. Dynamic current peaks are eliminated by a blocking cap (10 to 22 nF) between VDDI and GNDI. The total power consumption of 2EDi is dominated by the output side and depends on switching frequency, gate resistor and gate charge, while for typical switching frequencies the input supply current stays relatively constant (see Figure 6 to Figure 7). 3.3.2 Output-side power supply Each gate driver channel has to be powered separately. It is recommended to use a ceramic bypass capacitor (minimum value 20 × Ciss of MOSFET) from VDDA to GNDA and from VDDB to GNDB in close proximity to the device. The operating supply voltage can range from 4.5 V to 20 V for each gate drive channel. The minimum gate driver turn-on voltage is set by the device Undervoltage Lockout (UVLO) to protect the power MOSFETs from operating in the saturation region. Devices with 4 V, 8 V and 13 V UVLO thresholds for the output supply are currently available (see Chapter 1.1). Table 3 Isolation type Potential applications Functional • High-power hard-switching high-voltage PFC, Vienna Rectifier, Totem Pole PFC or Synchronous Rectification • Driving switches with Kelvin source connection (4-pin package) • Secondary-side control in low voltage isolated DC/DC topologies and brick converters Reinforced • Secondary-side control of high voltage SJ-MOSFETs in LLC or PS-ZVS • Primary-side controlled synchronous rectification • 1 A/2 A PWM data-/signal-coupler for local boost gate drivers |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |