| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
SPC574KX bảng dữ liệu(PDF) 87 Page - STMicroelectronics |
|
|
|||||||||||||||||||||||||||||
SPC574KX bảng dữ liệu(HTML) 87 Page - STMicroelectronics |
|
87 / 160 page ![]() DocID023601 Rev 6 87/160 SPC574Kx Electrical characteristics 159 tESUS Erase suspend latency(11) —— — — — — 20 T µs tAIC0S Array Integrity Check (2.5 MB, sequential)(12) 25 T — — — — — — — ms tAIC256KS Array Integrity Check (256 KB, sequential)(12) 2.5 T — — — — — — — ms tAIC0P Array Integrity Check (2.5 MB, proprietary)(12) 2.5 T — — — — — — — s tMR0S Margin Read (2.5 MB, sequential)(12) 125 T — — — — — — — ms tMR256KS Margin Read (256 KB, sequential)(12) 12.5 T — — — — — — — ms 1. Characteristics are valid both for Data Flash and Code Flash, unless specified in the characteristics column. 2. Actual hardware programming times; this does not include software overhead. 3. Typical program and erase times assume nominal supply values and operation at 25 °C. All times are subject to change pending device characterization. 4. Typical End of Life program and erase times represent the median performance and assume nominal supply values. Typical End of Life program and erase values may be used for throughput calculations. These values are characteristic, but not tested. 5. Lifetime maximum program & erase times apply across the voltages and temperatures and occur after the specified number of program/erase cycles. These maximum values are characterized but not tested or guaranteed. 6. Initial factory condition: < 100 program/erase cycles, 20 °C < TJ < 30 °C junction temperature, and nominal (± 2%) supply voltages. These values are verified at production testing. 7. Initial maximum “All temp” program and erase times provide guidance for time-out limits used in the factory and apply for less than or equal to 100 program or erase cycles, –40 °C < TJ < 150 °C junction temperature, and nominal (± 2%) supply voltages. These values are verified at production testing. 8. Rate computed based on 256 K sectors. 9. Only code sectors, not including EEPROM. 10. Time between suspend resume and next suspend. Value stated actually represents minimum value specification. 11. Timings guaranteed by design. 12. AIC is done using system clock, thus all timing is dependant on system frequency and number of wait states. Timing in the table is calculated at max frequency. Table 45. Flash memory program and erase specifications (1)(Continued) Symbol Characteristics(2) Value Unit Typ(3) C Initial max Typical end of life(4) Lifetime max(5) C 25 °C(6) All temp (7) C < 1 k cycles < 250 K cycles Table 46. Flash memory Life Specification Symbol Characteristics(1) Value Unit Min C Typ C NCER16K 16 KB CODE Flash endurance 10 — 100 — kcycles NCER32K 32 KB CODE Flash endurance 10 — 100 — kcycles NCER64K 64 KB CODE Flash endurance 10 — 100 — kcycles |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |