| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
SPC574KX bảng dữ liệu(PDF) 70 Page - STMicroelectronics |
|
|
|||||||||||||||||||||||||||||
SPC574KX bảng dữ liệu(HTML) 70 Page - STMicroelectronics |
|
70 / 160 page ![]() Electrical characteristics SPC574Kx 70/160 DocID023601 Rev 6 tSETTLING CC D Settling time after mux change(19) Analog inputs are muxed HPF = ON —— 2* δGROUP + 3*fADCD_S — HPF = OFF — — 2* δGROUP + 2*fADCD_S — tODRECOVERY CC D Overdrive recovery time After input comes within range from saturation HPF = ON —— 2* δGROUP + fADCD_S — HPF = OFF — — 2* δGROUP — CS_D CC D S/D ADC sampling capacitance after sampling switch(19) GAIN = 1, 2, 4, 8 — — 75*GAIN fF DGAIN = 16 — — 600 fF IBIAS CC D Bias consumption At least 1 ADCD enabled — — 3.5 mA IADV_D CC T VDD_HV_ADV power supply current (each ADC) ADCD enabled — — 3.5 mA P Sum of all ADCs + BIAS — — 10.5 ΣIADR_D CC P Sum of all ADC reference consumption(20) ADCD enabled — — 30 µA IADCS/D_REFH CC T S/D ADC Reference High Current Dynamic consumption (Conversion) —— 3.5 µA T Static consumption (Power-down mode and bias) —— +10 1. Functional operating conditions are given in the DC electrical specifications. Absolute maximum ratings are stress ratings only, and functional operation at the maxima is not guaranteed. Stress beyond the listed maxima may affect device reliability or cause permanent damage to the device. 2. For input voltage above the maximum and below the clamp voltage of the input pad, there is no latch-up concern, and the signal will only be ‘clipped’. 3. VINP is the input voltage applied to the positive terminal of the SDADC. 4. Maximum input of 166.67 kHz supported with reduced accuracy. See SNR specifications. 5. When using a GAIN setting of 16, the conversion result will always have a value of zero in the least significant bit. The gives an effective resolution of 15 bits. 6. Offset and gain error due to temperature drift can occur in either direction (+/-) for each of the SDADCs on the device. 7. Calibration of gain is possible when gain = 1. Offset Calibration should be done with respect to 0.5*VDD_HV_ADR for differential mode and single ended mode with negative input=0.5*VDD_HV_ADR. Offset Calibration should be done with respect to 0 for “single ended mode with negative input=0”. Both offset and Gain Calibration is guaranteed for ±5% variation of VDD_HV_ADR, ±10% variation of VDD_HV_ADV, and ± 50 °C temperature variation. 8. Conversion offset error must be divided by the applied gain factor (1, 2, 4, 8, or 16) to obtain the actual input referred offset error. 9. This parameter is guaranteed by bench validation with a small sample of devices across process variations, and tested in production to a value of 3 dB less. 10. S/D ADC is functional in the range 3.6 V – 4.5 V, SNR parameter degrades by 3 dB. Degraded SNR value based on simulation. Table 34. SDn ADC electrical specification(1)(Continued) Symbol C Parameter Conditions Value Unit Min Typ Max |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |