| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
ADS1282IPW.B bảng dữ liệu(PDF) 22 Page - Texas Instruments |
|
|
|||||||||||||||||||||||||||||
ADS1282IPW.B bảng dữ liệu(HTML) 22 Page - Texas Instruments |
|
22 / 54 page ![]() 0.01 0.1 NormalizedFrequency(f/f ) C 0 -7.5 -15.0 -22.5 -30.0 -45.0 90 75 60 45 30 15 0 1 10 100 Phase Amplitude -37.5 FrequencyRatio(f /f ) HP DATA 0 -0.10 -0.20 -0.30 -0.40 -0.50 0.0001 0.001 0.01 0.1 ADS1282 SBAS418I – SEPTEMBER 2007 – REVISED MARCH 2015 www.ti.com Group Delay and Step Response (continued) 9.16 Master Clock Input (CLK) The ADS1282 requires a clock input for operation. The HPF causes a small gain error, in which case the The clock is applied to the CLK pin. The data magnitude of the error depends on the ratio of conversion rate scales directly with the CLK fHP/fDATA. For many common values of (fHP/fDATA), the frequency. Power consumption versus CLK frequency gain error is negligible. Figure 45 shows the gain is relatively constant (see the Typical Characteristics). error of the HPF. The gain error factor is illustrated in Equation 13 (see the Appendix at the end of this As with any high-speed data converter, a high-quality, document). low-jitter clock is essential for optimum performance. Crystal clock oscillators are the recommended clock source. Make sure to avoid excess ringing on the clock input; keep the clock trace as short as possible and use a 50 Ω series resistor close to the source. 9.17 Synchronization (Sync Pin and Sync Command) The ADS1282 can be synchronized to an external event, as well as synchronized to other ADS1282 devices if the sync event is applied simultaneously. The ADS1282 has two sources for synchronization: the SYNC input pin and the SYNC command. The ADS1282 also has two synchronizing modes: Pulse- sync and Continuous-sync. In Pulse-sync mode, the ADS1282 synchronizes to a single sync event. In Continuous-sync mode, either a single SYNC event is Figure 45. HPF Gain Error used to synchronize conversions or a continuous clock is applied to the pin with a period equal to Figure 46 shows the first-order amplitude and phase integer multiples of the data rate. When the periods of response of the HPF. Note that in the case of the sync input and the DRDY output do not match, applying step inputs or synchronizing, the settling the ADS1282 re-synchronizes and conversions are time of the filter should be taken into account. restarted. Figure 46. HPF Amplitude and Phase Response 22 Submit Documentation Feedback Copyright © 2007–2015, Texas Instruments Incorporated Product Folder Links: ADS1282 |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |