| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
PCM1796DBR.B bảng dữ liệu(PDF) 29 Page - Texas Instruments |
|
|
|||||||||||||||||||||||||||||
PCM1796DBR.B bảng dữ liệu(HTML) 29 Page - Texas Instruments |
|
29 / 63 page ![]() PCM1796 SLES100A − DECEMBER 2003 − REVISED NOVEMBER 2006 www.ti.com 29 OPE: DAC Operation Control This bit is available for read and write. Default value: 0 OPE = 0 DAC operation enabled (default) OPE = 1 DAC operation disabled The OPE bit is used to enable or disable the analog output for both channels. Disabling the analog outputs forces them to the bipolar zero level (BPZ) even if audio data is present on the input. DFMS: Stereo DF Bypass Mode Select This bit is available for read and write. Default value: 0 DFMS = 0 Monaural (default) DFMS = 1 Stereo input enabled The DFMS bit is used to enable stereo operation in DF bypass mode. In the DF bypass mode, when DFMS is set to 0, the pin for the input data is DATA (pin 5) only, therefore the PCM1796 operates as a monaural DAC. When DFMS is set to 1, the PCM1796 can operate as a stereo DAC with inputs of L-channel and R-channel data on ZEROL (pin 1) and ZEROR (pin 2), respectively. FLT: Digital Filter Rolloff Control This bit is available for read and write. Default value: 0 FLT = 0 Sharp rolloff (default) FLT = 1 Slow rolloff The FLT bit is used to select the digital filter rolloff characteristic. The filter responses for these selections are shown in the TYPICAL PERFORMANCE CURVES section of this data sheet. INZD: Infinite Zero Detect Mute Control This bit is available for read and write. Default value: 0 INZD = 0 Infinite zero detect mute disabled (default) INZD = 1 Infinite zero detect mute enabled The INZD bit is used to enable or disable the zero detect mute function. Setting INZD to 1 forces muted analog outputs to hold a bipolar zero level when the PCM1796 detects a zero condition in both channels. The infinite zero detect mute function is not available in the DSD mode. B15 B14 B13 B12 B11 B10 B9 B8 B7 B6 B5 B4 B3 B2 B1 B0 Register 20 R/W 0 0 1 0 1 0 0 RSV SRST DSD DFTH MONO CHSL OS1 OS0 R/W: Read/Write Mode Select When R/W = 0, a write operation is performed. When R/W = 1, a read operation is performed. Default value: 0 |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |