| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
TMP86FS49AIUG bảng dữ liệu(PDF) 113 Page - Toshiba Semiconductor |
|
|
|||||||||||||||||||||||||||||
TMP86FS49AIUG bảng dữ liệu(HTML) 113 Page - Toshiba Semiconductor |
|
113 / 296 page ![]() Page 97 TMP86FS49AIUG 9.3.2 Event counter mode In this mode, events are counted on the rising edge of the TC2 pin input. The contents of TC2DR are com- pared with the contents of the up counter. If a match is found, an INTTC2 interrupt is generated, and the counter is cleared. Counting up is resumed every the rising edge of the TC2 pin input after the up counter is cleared. Match detect is executed on the falling edge of the TC2 pin. Therefore, an INTTC2 interrupt is generated at the falling edge after the match of TC2DR and up counter. The minimum input pulse width of TC2 pin is shown in Table 9-2. Two or more machine cycles are required for both the “H” and “L” levels of the pulse width. Figure 9-3 Event Counter Mode Timing Chart 9.3.3 Window mode In this mode, counting up performed on the rising edge of an internal clock during TC2 external pin input (Window pulse) is “H” level. The contents of TC2DR are compared with the contents of up counter. If a match found, an INTTC2 interrupt is generated, and the up-counter is cleared. The maximum applied frequency (TC2 input) must be considerably slower than the selected internal clock by the TC2CR<TC2CK>. Note:It is not available window mode in the SLOW/SLEEP mode. Therefore, at the window mode in NORMAL mode, the timer should be halted by setting TC2CR<TC2S> to "0" before the SLOW/SLEEP mode is entered. Example :Sets the event counter mode and generates an INTTC2 interrupt 640 counts later. LDW (TC2DR), 640 ; Sets TC2DR DI ; IMF= “0” SET (EIRE). 6 ;Enables INTTC2 interrupt EI ; IMF= “1” LD (TC2CR), 00011100B ; TC2 source clock / mode select LD (TC2CR), 00111100B ; Starts TC2 Table 9-2 Timer/Counter 2 External Input Clock Pulse Width Minimum Input Pulse Width [s] NORMAL1/2, IDLE1/2 mode SLOW1/2, SLEEP1/2 mode “H” width 23/fc 23/fs “L” width 23/fc 23/fs n INTTC2 interrupt TC2 pin input Counter TC2DR Match detect Counter clear Timer start 0 1 2 3 n 0 1 2 3 |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |