TMP86CS44UG datasheet(44/172 Pages) TOSHIBA

44 / 172 page

Page 34

3. Interrupt Control Circuit

3.2 Interrupt enable register (EIR)

TMP86CS44UG

Interrupt latches are not set to “1” by an instruction.

Since interrupt latches can be read, the status for interrupt requests can be monitored by software.

Note: In main program, before manipulating the interrupt enable flag (EF) or the interrupt latch (IL), be sure to clear IMF to

"0" (Disable interrupt by DI instruction). Then set IMF newly again as required after operating on the EF or IL

(Enable interrupt by EI instruction)

In interrupt service routine, because the IMF becomes "0" automatically, clearing IMF need not execute normally on

interrupt service routine. However, if using multiple interrupt on interrupt service routine, manipulating EF or IL

should be executed before setting IMF="1".

3.2 Interrupt enable register (EIR)

The interrupt enable register (EIR) enables and disables the acceptance of interrupts, except for the non-maskable

interrupts (Software interrupt, undefined instruction interrupt, address trap interrupt and watchdog interrupt). Non-

maskable interrupt is accepted regardless of the contents of the EIR.

The EIR consists of an interrupt master enable flag (IMF) and the individual interrupt enable flags (EF). These

registers are located on address 003AH and 003BH in SFR area, and they can be read and written by an instructions

(Including read-modify-write instructions such as bit manipulation or operation instructions).

3.2.1 Interrupt master enable flag (IMF)

The interrupt enable register (IMF) enables and disables the acceptance of the whole maskable interrupt.

While IMF = “0”, all maskable interrupts are not accepted regardless of the status on each individual interrupt

enable flag (EF). By setting IMF to “1”, the interrupt becomes acceptable if the individuals are enabled. When

an interrupt is accepted, IMF is cleared to “0” after the latest status on IMF is stacked. Thus the maskable inter-

rupts which follow are disabled. By executing return interrupt instruction [RETI/RETN], the stacked data,

which was the status before interrupt acceptance, is loaded on IMF again.

The IMF is located on bit0 in EIRL (Address: 003AH in SFR), and can be read and written by an instruction.

The IMF is normally set and cleared by [EI] and [DI] instruction respectively. During reset, the IMF is initial-

ized to “0”.

3.2.2 Individual interrupt enable flags (EF15 to EF4)

Each of these flags enables and disables the acceptance of its maskable interrupt. Setting the corresponding

bit of an individual interrupt enable flag to “1” enables acceptance of its interrupt, and setting the bit to “0” dis-

ables acceptance. During reset, all the individual interrupt enable flags (EF15 to EF4) are initialized to “0” and

all maskable interrupts are not accepted until they are set to “1”.

Note:In main program, before manipulating the interrupt enable flag (EF) or the interrupt latch (IL), be sure to clear

IMF to "0" (Disable interrupt by DI instruction). Then set IMF newly again as required after operating on the EF

or IL (Enable interrupt by EI instruction)

In interrupt service routine, because the IMF becomes "0" automatically, clearing IMF need not execute nor-

Example 1 :Clears interrupt latches

; IMF

← 0

LDW

(ILL), 1110100000111111B

; IL12, IL10 to IL6

← 0

; IMF

← 1

Example 2 :Reads interrupt latchess

WA, (ILL)

; W

← ILH, A ← ILL

Example 3 :Tests interrupt latches

TEST

(ILL). 7

; if IL7 = 1 then jump

F, SSET

TMP86CS44UG bảng dữ liệu(PDF) 44 Page - Toshiba Semiconductor

TMP86CS44UG bảng dữ liệu(HTML) 44 Page - Toshiba Semiconductor

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL