| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
TMP88CS38BFG bảng dữ liệu(PDF) 94 Page - Toshiba Semiconductor |
|
|
|||||||||||||||||||||||||||||
TMP88CS38BFG bảng dữ liệu(HTML) 94 Page - Toshiba Semiconductor |
|
94 / 218 page ![]() TMP88CS38B/CM38B/CP38B 2007-09-12 88CS38B-94 (7) Start/stop condition generation When the BB (Bit5 in SBICRB) is “0”, a slave address and a direction bit which are set to the SBIDBR are output on a bus after generating a start condition by writing “1” to the MST, TRX, BB and PIN. It is necessary to set transmitted data to the SBIDBR and set “1” to ACK beforehand. Figure 2.9.9 Start Condition Generation and Slave Address Generation When the BB is “1”, sequence of generating a stop condition is started by writeng “1” to the MST, TRX and PIN, and “0” to the BB. Do not modify the contents of MST, TRX, BB and PIN until a stop condition is generated on a bus. Figure 2.9.10 Stop Condition Generation When a stop condition is generated and the SCL line on a bus is pulled down to low level by another device, a stop condition is generated after releasing the SCL line. The bus condition can be indicated by reading the contents of the BB (Bit5 in SBISRB). The BB is set to “1” when a start condition on a bus is detected and is cleared to “0” when a stop condition is detected. (8) Interrupt service request and cancel When a serial bus interface circuit is in the master mode and transferring a number of clocks set by the BC and the ACK is complete, a serial bus interface interrupt request (INTSBI) is generated. In the slave mode, the conditions of generating INTSBI are follows: • At the end of acknowledge signal when the received slave address matches to the value set by the I2CAR • At the end of acknowledge signal when a “GENERAL CALL” is received • At the end of transferring or receiving after matching of slave address or receiving of “GENRAL CALL” When a serial bus interface interrupt request occurs, the PIN (Bit4 in SBISR) is cleared to “0”. During the time that the PIN is “0”, the SCL pin is pulled down to low level. Either writing data to SBIDBR or reading data from the SBIDBR sets the PIN to “1”. The time from the PIN being set to “1” until the SCL pin is released takes tLOW. Although the PIN (Bit4 in SBICRB) can be set to “1” by the program, the PIN can not be cleared to “0” by the program. Note: If the arbitration lost occurs, when the slave address does not match, the PIN is not cleared to “0” even thought INTSBI is generated. SCL pin SDA pin Start condition slave address and the direction bit Acknowledge signal 1 2 345678 9 A6 A5 A4 A3 A2 A1 A0 R/ W SDA pin SCL pin Stop condition |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |