| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
TMPR3927 bảng dữ liệu(PDF) 96 Page - Toshiba Semiconductor |
|
|
|||||||||||||||||||||||||||||
TMPR3927 bảng dữ liệu(HTML) 96 Page - Toshiba Semiconductor |
|
96 / 512 page ![]() Chapter 8 SDRAM Controller 8-12 8.4.6 SDRAM Command Register (SDCCMD) 0xFFFE_802C 31 24 23 16 Model Number Version Number RR : Type 0x20 0x10 : Initial value 15 12 11 4 3 0 0 SDCMSK SDCMD R/W R/W : Type 0x00 0x0 : Initial value Bits Mnemonic Field Name Description 31 : 24 Model Number Model Number Model Number (initial value: 0x20) Shows the model number. The TX3927’s model number is 0x20. The field is read-only. 23 : 16 Version Number Version Number Version Number (initial value: 0x10) Shows the version number. The TX3927’s version number is 0x10. The field is read-only. 11 : 4 SDCMSK Channel Mask Channel Mask (initial value: 0x00) A “1” enables the command for the corresponding channel. The command is executed in parallel on all enabled channels. 1 Bit 11: Channel 7 Bit 10: Channel 6 Bit 9: Channel 5 Bit 8: Channel 4 Bit 7: Channel 3 Bit 6: Channel 2 Bit 5: Channel 1 Bit 4: Channel 0 3 : 0 SDCMD Command Command (initial value: 0x0) Selects the command for memory. 0x0: NOP command 0x1: Set the SDRAM/SGRAM mode register. 0x2: Set the SMROM mode register. 0x3: Precharge all SDRAM/SGRAM banks (PALL). 0x4: Enter low power mode. 0x5: Enter power-down mode. 0x6: Exit low power/power-down mode. 0x7-0xf: Reserved Commands will only be executed on channels with a memory type of SDRAM, SMROM, or SGRAM. Low power mode is self-refresh mode for SDRAMs/SGRAMs and low power mode for SMROMs. Power-down mode is precharge power-down mode for SDRAMs/SGRAMs and low power mode for SMROMs. Note 1: The mask bits are also used for the SGRAM load mask and load color registers. Any write cycle for the command register will wait until the command is executed. Therefore, memory cycles cannot be executed until the command cycle is executed. The command cannot start until the SDRAMC becomes idle. First use the channel control register to enable the target channel before executing a command for the channel. Commands will only be executed on channels enabled with the channel control register. Figure 8.4.5 SDRAM Command Register |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |