| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
RT9202GS bảng dữ liệu(PDF) 12 Page - Richtek Technology Corporation |
|
|
|||||||||||||||||||||||||||||
RT9202GS bảng dữ liệu(HTML) 12 Page - Richtek Technology Corporation |
|
12 / 14 page ![]() RT9202 12 DS9202-09 March 2007 www.richtek.com Figure 6 Loop Gain 40 30 20 10 1M 10k 1k 100 100k V OUT = 3.3V C OUT = 1500 µF(33mΩ) L = 2 µH V OUT = 1.5V V OUT = 2.5V V OUT = 3.3V P O = 2.9kHz Z O = 3.2kHz Reference Voltage Because RT9202 use a low 35dB gain error amplifier, shown in Figure 7. The voltage regulation is dependent on VIN & VOUT setting. The FB reference voltage of 0.8V were trimmed at VIN = 5V & VOUT = 2.5V condition. In a fixed VIN = 5V application, the FB reference voltage vs. VOUT voltage can be calculated as Figure 8. Figure 7 Figure 8 V OUT (V) 4 3.5 3 1 1.5 2 2.5 0.82 0.78 0.80 0.81 0.79 0.5 4.5 VIN = 5V Feedback Divider The reference of RT9202 is 0.8V. The output voltage can be set using a resistor based divider as shown in Figure 9. Put the R1 and R2 as close as possible to FB pin and R2 should less than 1 k Ω to avoid noise coupling. The C1 capacitor is a speed-up capacitor for reducing output ripple to meet with the requirement of fast transient load. Typically a 1nF to 0.1 µF is enough for C1. Figure 9 V IN R1 C1 FB RT9202 V OUT L R2 <1K C OUT PWM Layout Considerations MOSFETs switch very fast and efficiently. The speed with which the current transitions from one device to another causes voltage spikes across the interconnecting impedances and parasitic circuit elements. The voltage spikes can degrade efficiency and radiate noise, that results in over-voltage stress on devices. Careful component placement layout and printed circuit design can minimize the voltage spikes induced in the converter. Consider, as an example, the turn-off transition of the upper MOSFET prior to turn-off, the upper MOSFET was carrying the full load current. During turn-off, current stops flowing in the upper MOSFET and is picked up by the low side MOSFET or Schottky diode. Any inductance in the switched current path generates a large voltage spike during the switching interv al. Careful component selections, layout of the critical components, and use shorter and wider PCB traces help in minimizing the magnitude of voltage spikes. + - EA + - PWM 56K 1K + - FB REP 0.8V RAMP 1.75V R1 R2 |
|
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |