MPC8280 datasheet(716/1386 Pages) FREESCALE

716 / 1386 page

SCC UART Mode

MPC8280 PowerQUICC II Family Reference Manual, Rev. 1

21-10

Freescale Semiconductor

Table 21-5 describes TOSEQ fields.

21.12 Sending a Break (Transmitter)

A break is an all-zeros character with no stop bit that is sent by issuing a STOP TRANSMIT command. The

SCC finishes transmitting outstanding data, sends a programmable number of break characters

(determined by BRKCR), and reverts to idle or sends data if a RESTART TRANSMIT command is given

before completion. When the break code is complete, the transmitter sends at least one high bit before

sending more data, to guarantee recognition of a valid start bit. Because break characters do not preempt

characters in the transmit FIFO, they may not be sent for eight (SCC) or four (SCC) character times. To

reduce this latency, set GSMR_H[TFL] to decrease the FIFO size to one character before enabling the

transmitter.

21.13 Sending a Preamble (Transmitter)

Sending a preamble sequence of consecutive ones ensures that a line is idle before sending a message. If

the preamble bit TxBD[P] is set, the SCC sends a preamble sequence (idle character) before sending the

buffer. For example, for 8 data bits, no parity, 1 stop bit, and 1 start bit, a preamble of 10 ones is sent before

the first character in the buffer.

Field

—

REA

—

CHARSEND

Reset

0000_0000_0000_0000

R/W

Addr

SCC base + 0x4E

Figure 21-4. Transmit Out-of-Sequence Register (TOSEQ)

Table 21-5. TOSEQ Field Descriptions

Bit

Name

Description

0–1

—

Reserved, should be cleared.

REA

Ready. Set when the character is ready for transmission. Remains 1 while the character is being

sent. The CP clears this bit after transmission.

Interrupt. If this bit is set, transmission completion is flagged in the event register (SCCE[TX] is

set), triggering a maskable interrupt to the core.

Clear-to-send lost. Operates only if the SCC monitors CTS (GSMR_L[DIAG]). The CP sets this

bit if CTS negates when the TOSEQ character is sent. If CTS negates and the TOSEQ character

is sent during a buffer transmission, the TxBD[CT] status bit is also set.

5–6

—

Reserved, should be cleared.

Address. Setting this bit indicates an address character for multidrop mode.

8–15 CHARSEND Character send. Contains the character to be sent. Any 5- to 8-bit character value can be sent

in accordance with the UART configuration. The character should be placed in the lsbs of

CHARSEND. This value can be changed only while REA = 0.

MPC8280 bảng dữ liệu(PDF) 716 Page - Freescale Semiconductor, Inc

MPC8280 bảng dữ liệu(HTML) 716 Page - Freescale Semiconductor, Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL