SPSB100 datasheet(72/214 Pages) STMICROELECTRONICS

72 / 214 page

7.6

LDO2 voltage regulator

The voltages are referred to GND and currents are assumed positive, when the current flows into the pin.

6 V ≤ VFBB ≤ 29 V, Tj = -40 °C to 150 °C, unless otherwise specified.

The same parameter values in both 5 V and 3.3 V conditions applies unless otherwise specified.

Table 27. LDO2

Symbol

Parameter

Condition

Min

Typ

Max

Unit

VLDO2_5

Output voltage

VS ≥ 6.0 V

4.9

5.0

5.15

VLDO2_33

Output voltage

VS ≥ 6.0 V

3.23

3.3

3.399

VLDO2_ACC_25(1)

Output voltage tracking accuracy

ILOAD = 100 μA to 5 mA

VFBB = 8 V to 18 V

Tj = 25 °C

-10

VLDO2_ACC_130

Output voltage tracking accuracy

ILOAD = 100 μA to 5 mA

VFBB = 8 V to 18 V

Tj = 130 °C

-20

VLDO2_OV

Overvoltage threshold for LDO2

105

108.5

112

tLDO2_OV(2)

LDO2 overvoltage filter time

μs

VLDO2_PG

Power-good voltage threshold for LDO2

91.5

98.5

VLDO2_UV

Undervoltage threshold for LDO2

91.5

tLDOLDO2_UV(2)

LDO2 undervoltage filter time

μs

tLDO2_PG_TO(2)

LDO2 timeout for power-good

4.8

7.5

VLDO2_DP

Drop-out voltage

ILOAD = 10 mA

0.5

1.0

ILDO2_CCmax

Short circuit output current (to GND)

Current limitation

CLDO2(3)

Load capacitor1

Ceramic (± 20%)

µF

1. Guarantee by design.

2. Digital implementation is guaranteed by scan test.

3. Nominal capacitor value required for stability of the regulator. Tested with 1 µF ceramic (±20%). The capacitor must be

located close to the regulator output pin. A 2.2 μF capacitor value is recommended to minimize the DPI (Direct power

injection) stress in the application.

7.7

Boost controller

The voltages are referred to GND and currents are assumed positive, when the current flows into the pin.

3 V ≤ VS ≤ 29 V, Tj = -40 °C to 150 °C, unless otherwise specified.

Table 28. Boost controller

Symbol

Parameter

Condition

Min

Typ

Max Unit

VFBB_UV_R

BOOST rising enable threshold

Input voltage required on initial start-up

to enable the boost

5.0

5.25

5.5

VFBB_UV_F

BOOST falling disable threshold Power down threshold

4.65

4.9

5.15

VFBB_UV_HYS

Boost enable hysteresis

0.2

0.35

0.5

TF_FBB_UV(1)

digital filter time on FBB POR

µs

VFBB_REG1

VFBB regulation threshold

If BUCK1 and BUCK2 voltage settings

are = 3.3 V

7.7

8.0

8.3

VFBB_REG2

VFBB regulation threshold

If BUCK1 or BUCK2 voltage settings

are above 3.3 V (5.0 or 6.5 V)

9.2

9.5

9.8

SPSB100

Electrical characteristics

DS14640 - Rev 1

page 72/214

SPSB100 bảng dữ liệu(PDF) 72 Page - STMicroelectronics

SPSB100 bảng dữ liệu(HTML) 72 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL