| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
M420000055 bảng dữ liệu(PDF) 16 Page - Advanced Micro Devices |
|
|
|||||||||||||||||||||||||||||
M420000055 bảng dữ liệu(HTML) 16 Page - Advanced Micro Devices |
|
16 / 72 page ![]() November 1, 2002 Am42BDS640AG 15 P R E L I M INARY mode and uses the higher voltage on the input to reduce the time required for program operations. The system would use a two-cycle program command sequence as required by the Unlock Bypass mode. Removing V ID from the ACC input returns the device to normal operation. Note that sectors must be unlocked prior to raising ACC to V ID. Note that the ACC pin must not be at V ID for operations other than accelerated pro- gramming, or device damage may result. In addition, the ACC pin must not be left floating or unconnected; inconsistent behavior of the device may result. When at V IL, ACC locks all sectors. ACC should be at V IH for all other conditions. Autoselect Functions If the sy stem writes the autoselect c o mmand sequence, the device enters the autoselect mode. The system can then read autoselect codes from the internal register (which is separate from the memory array) on DQ15–DQ0. Autoselect mode may only be entered and used when in the asynchronous read mode. Refer to the “Autoselect Command Sequence” section on page 26 section for more information. Standby Mode When the system is not reading or writing to the device, it can place the device in the standby mode. In this mode, current consumption is greatly reduced, and the outputs are placed in the high impedance state, inde- pendent of the OE# input. The device enters the CMOS standby mode when the CE# and RESET# inputs are both held at V CC ± 0.2 V. The device requires standard access time (t CE) for read access, before it is ready to read data. If the device is deselected during erasure or program- ming, the device draws active current until the opera- tion is completed. I CC3 in the DC Characteristics table represents the standby current specification. Automatic Sleep Mode The automatic sleep mode minimizes Flash device energy consumption. While in asynchronous mode, the de vice au to matically enables this mo de w hen addresses remain stable for tACC + 60 ns. The auto- matic sleep mode is independent of the CE#, WE#, and OE# control signals. Standard address access timings provide new data when addresses are changed. While in sleep mode, output data is latched and always avail- able to the system. While in synchronous mode, the device automatically enables this mode when either the first active CLK edge occurs after tACC or the CLK runs slower than 5MHz. Note that a new burst opera- tion is required to provide new data. I CC4 in the “Flash DC Characteristics” section on page 36 represents the automatic sleep mode current spec- ification. RESET#: Hardware Reset Input The RESET# input provides a hardware method of resetting the device to reading array data. When RESET# is driven low for at least a period of t RP, the device immediately terminates any operation in progress, tristates all outputs, resets the configuration register, and ignores all read/write commands for the duration of the RESET# pulse. The device also resets the internal state machine to reading array data. The operation that was interrupted should be reinitiated once the device is ready to accept another command sequence, to ensure data integrity. Current is reduced for the duration of the RESET# pulse. When RESET# is held at V SS ± 0.2 V, the device draws CMOS standby current (I CC4). If RESET# is held at V IL but not within VSS ± 0.2 V, the standby current will be greater. RESET# may be tied to the system reset circuitry. A system reset would thus also reset the Flash memory, enabling the system to read the boot-up firmware from the Flash memory. If RESET# is asserted during a program or erase oper- ation, the device requires a time of t READY (during Embedded Algorithms) before the device is ready to read data again. If RESET# is asserted when a program or erase operation is not executing, the reset operation is completed within a time of t READY (not during Embedded Algorithms). The system can read data t RH after RESET# returns to VIH. Refer to the AC Characteristics tables for RESET# parameters and to Figure 20, “Reset Timings,” on page 49 for the timing diagram. Output Disable Mode When the OE# input is at V IH, output from the device is disabled. The outputs are placed in the high imped- ance state. Hardware Data Protection The command sequence requirement of unlock cycles for programming or erasing provides data protection against inadvertent writes (refer to Table 14, “Com- mand Definitions,” on page 30 for command defini- tions). The device offers two types of data protection at the sector level: ■ The sector lock/unlock command sequence dis- ables or re-enables both program and erase opera- tions in any sector. |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |