| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
WM9714LGEFL/V bảng dữ liệu(PDF) 24 Page - Wolfson Microelectronics plc |
|
|
|||||||||||||||||||||||||||||
WM9714LGEFL/V bảng dữ liệu(HTML) 24 Page - Wolfson Microelectronics plc |
|
24 / 94 page ![]() WM9714L Pre-Production w PP Rev 3.0 June 2006 24 REGISTER ADDRESS BIT LABEL DEFAULT DESCRIPTION 3:2 WL 00 PCM Data Word Length 11 = 32 bits (see Note) 10 = 24 bits 01 = 20 bits 00 = 16 bits 1:0 FMT 11 PCM Data Format Select 11 = DSP Mode 10 = I 2S Format 01 = Left justified 00 = Right justified Table 8 PCM Codec Control Note: Right justified does not support 32-bit data. AUDIO ADCS STEREO ADC The WM9714L has a stereo sigma-delta ADC to digitize audio signals. The ADC achieves high quality audio recording at low power consumption. The ADC sample rate can be controlled by writing to a control register (see “Variable Rate Audio”). It is independent of the DAC sample rate. To save power, the left and right ADCs can be separately switched off using the Powerdown bits ADCL and ADCR (register 3Ch, bits 5:4), whereas PR0 disables both ADCs (see “Power Management” section). If only one ADC is running, the same ADC data appears on both the left and right AC-Link slots. The output from the ADC can be sent over either the AC link as usual, or output via the PCM interface which may be configured on the GPIO pins. HIGH PASS FILTER The WM9714L audio ADC incorporates a digital high pass filter that eliminates any DC bias from the ADC output data. The filter is enabled by default. For DC measurements, it can be disabled by writing a ‘1’ to the HPF bit (register 5Ch, bit 3). This high pass filter corner frequency can be selected to have different values in WM9714L, to suit applications such as voice where a higher cutoff frequency is required. REGISTER ADDRESS BIT LABEL DEFAULT DESCRIPTION 5Ch 3 HPF 0 High-pass filter disable 0: Filter enabled (for audio) 1: Filter disabled (for DC measurements) 5Ah 5:4 HPMODE 00 HPF corner frequency 00: 7Hz @ Fs=48kHz 01: 82Hz @ Fs=16kHz 10: 82Hz @ Fs=8kHz 11: 170Hz @ Fs=8kHz Note: the filter corner frequency is proportional to the sample rate. Table 9 Controlling the ADC Highpass Filter ADC SLOT MAPPING By default, the output of the left audio ADC appears on slot 3 of the SDATAIN signal (pin 8), and the right ADC data appears on slot 4. However, the ADC output data can also be sent to other slots, by setting the ASS (ADC slot select) control bits as shown below. |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |