| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
WM9714LGEFL/V bảng dữ liệu(PDF) 55 Page - Wolfson Microelectronics plc |
|
|
|||||||||||||||||||||||||||||
WM9714LGEFL/V bảng dữ liệu(HTML) 55 Page - Wolfson Microelectronics plc |
|
55 / 94 page ![]() Pre-Production WM9714L w PP Rev 3.0 June 2006 55 In a polling routine, the CPU starts each measurement individually by writing to the POLL bit (register 74h, bit 9). This bit automatically resets itself when the measurement is completed. REGISTER ADDRESS BIT LABEL DEFAULT DESCRIPTION 9 POLL 0 Writing “1” initiates a measurement. (when CTC is not set) 74h 8 CTC 0 0: Polling mode 1: Continuous mode (for DMA) 76h 9:8 CR 00 Continuous mode rate (DEL C 1111) 00: 93.75 Hz (every 512 AC-Link frames) 01: 120 Hz (every 400 AC-Link frames) 10: 153.75 Hz (every 312 AC-Link frames) 11: 187.5Hz (every 256 AC-Link frames) Continuous mode “fast rate” (DEL = 1111) 00: 8 kHz (every six AC-Link frames) 01: 12 kHz (every four AC-Link frames) 10: 24 kHz (every other AC-Link frame) 11: 48 kHz (every AC-Link frame) Table 47 AUX ADC Control (Initiation of Measurements) In continuous mode (CTC = 1), the WM9714L autonomously initiates measurements (or sets of measurements) at the rate set by CR, and supplies the measured data to the CPU on one of the unused AC’97 time slots. DMA-enabled CPUs can write the data directly into a FIFO without any intervention by the CPU core. This reduces CPU loading and speeds up the execution of user programs in handheld systems. Note that the measurement frequency in continuous mode is also affected by the DEL bits. The faster rates achieved when DEL = 1111 may be useful when the ADC is used for multiple measurements. MEASUREMENT TYPES The ADCSEL control bits determine which type of measurement is performed (see below). REGISTER ADDRESS BIT LABEL DEFAULT DESCRIPTION 9 POLL 0 Writing “1” initiates a measurement. (when CTC is not set) 8 CTC 0 0: Polling mode 1: Continuous mode (for DMA) 7 ADCSEL_AUX4 0 Enable COMP1/AUX4 measurement (pin32). NB: Only one of bits[7:4] should be set. 6 ADCSEL_AUX3 0 Enable COMP1/AUX3 measurement (pin31) . NB: Only one of bits[7:4] should be set. 5 ADCSEL_AUX2 0 Enable COMP1/AUX2 measurement (pin30) . NB: Only one of bits[7:4] should be set. 74h 4 ADCSEL_AUX1 0 Enable COMP1/AUX1 measurement (pin29) . NB: Only one of bits[7:4] should be set. Table 48 AUX ADC Control (Measurement Types) The WM9714L performs a single measurement – either in polling mode or continuously, as indicated by the CTC bit. The type of measurement is specified by the ADCSEL[7:4] bits. Only one of the ADCSEL[7:4] bits should be set. |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |