công cụ tìm kiếm bảng dữ liệu linh kiện điện tử
  Vietnamese  ▼
ALLDATASHEET.VN

X  

TLK2218ZPV bảng dữ liệu(PDF) 10 Page - Texas Instruments

tên linh kiện TLK2218ZPV
Giải thích chi tiết về linh kiện  8-PORT GIGABIT ETHERNET TRANSCEIVER
PDF  39 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
nhà sản xuất  TI [Texas Instruments]
Trang chủ  http://www.ti.com
Logo TI - Texas Instruments

TLK2218ZPV bảng dữ liệu(HTML) 10 Page - Texas Instruments

Back Button TLK2218ZPV Datasheet HTML 6Page - Texas Instruments TLK2218ZPV Datasheet HTML 7Page - Texas Instruments TLK2218ZPV Datasheet HTML 8Page - Texas Instruments TLK2218ZPV Datasheet HTML 9Page - Texas Instruments TLK2218ZPV Datasheet HTML 10Page - Texas Instruments TLK2218ZPV Datasheet HTML 11Page - Texas Instruments TLK2218ZPV Datasheet HTML 12Page - Texas Instruments TLK2218ZPV Datasheet HTML 13Page - Texas Instruments TLK2218ZPV Datasheet HTML 14Page - Texas Instruments Next Button
Zoom Inzoom in Zoom Outzoom out
 10 / 39 page
background image
www.ti.com
Miscellaneous Signals
TLK2218
SLLS734 – FEBRUARY 2007
SIGNAL
LOCATION
TYPE
DESCRIPTION
CODE
J2
LVCMOS
Encode enable. When high, the 8b/10b encoder and decoder are enabled. The logic value of
input with
this terminal is logically ORed with MDIO register 17.7 (8b/10b_EN).
P/D
CV_DIS_EN
J3
LVCMOS
Code violation/disparity error code enable. When CV_DIS_EN is high, the outputs RDxx[9:0]
input with
are set to 1 when a code violation or disparity error is detected. The logic value of this terminal
P/D
is logically ORed with the MDIO register 17.14 (CVDispEn).
This requires CODE to be enabled.o
RESET
G3
LVCMOS
Chip reset (FIFO clear). Pulling this terminal high recenters the transmit skew buffers, recenters
input with
receive channel synchronization FIFOs, and resets MDIO flags.
P/D
LPBK
D7
LVCMOS
Serial loopback enable. When asserted high, the outputs of the 8b/10b encoder are looped into
input with
the inputs of the 8b/10b decoder for each channel. The serial transmit outputs are driven to a
P/D
static state and the serial inputs are ignored.
MODE0
P11
LVCMOS
Configuration terminal. This terminal puts the device in full rate or half rate mode.
input with
MODE[0]
P/D
0 – Full rate mode
1 – Half rate mode
MODE1
P12
LVCMOS
Configuration terminal. This terminal puts the device under one of the following operation
input with
modes:
P/D
MODE[1]
0 – Multiplexed channel mode
1 – Nibble interface mode
ENABLE
D13
LVCMOS
Device enable. Pulling this terminal high enables all outputs of the device. A low on this
input with
terminal places all outputs for the device in the high-impedance state.
P/U
TCLKSEL
D9
LVCMOS
Transfer clock select. This terminal controls clock selection mode between synchronized and
input
independent channel mode.
In independent channel mode (TCLKSEL = 1) channels are clocked in and out by independent
clocks TLCK[B:H] and RBC[A:H], respectively. In synchronized channel mode (TCLKSEL = 0)
transmit and receive clocks are centered around TCLKB and RCLK/RBCH.
The logic value of this signal is ORed with TransClkMode, MDIO register R17.15.
BUSYEN
P9
LVCMOS
Busy mode enable. When asserted high, /K28.5/D10.1/ are treated as valid data and passed
input with
through the FIFO. When in the low state it causes high /K28.5/D10.1/ to be treated as an IDLE
P/U
sequence that can be deleted.
PLL_LOCK
R11
LVCMOS
PLL lock. When asserted high, this terminal provides an indication that sufficient time has
output
elapsed after a power-cycle or power-down sequence to ensure that PLLs have achieved lock.
GE_MOD
C8
LVCMOS
Gigabit Ethernet mode. When driven high, the chip:
input
1) Treats /K28.5/ followed by any valid data character as an IDLE sequence, except that
when BMOD is asserted, the chip treats /K28.5/D10.1/ as described in the BMOD
terminal description.
2) Modifies IDLE to correct disparity by substituting /D5.6/ for /D16.2/ in a /K28.5/Dx.y/
transmit IDLE pair.
The logic value of the GE_MOD terminal is ORed with GEMODE register 24.15.
PRBSEN
C13
LVCMOS
PRBS enable. When this terminal is asserted high, the pseudorandom bit stream generator and
input with
comparator circuits are inserted into the transmit and receive data paths on all channels,
P/D
respectively.
If this terminal is not used it can be tied to the GND reference.
TX+/TX– are transmitting 27-1 PRBS. RX+/RX– are comparing incoming data to an internally
generated 27-1 PRBS. Results of the RX comparison can be read from the MDIO.
10
Submit Documentation Feedback



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39


bảng dữ liệu tải về

Go To PDF Page


Link URL



Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không?  [ DONATE ] 

Alldatasheet là   |   Quảng cáo   |   Liên lạc với chúng tôi   |   Chính sách bảo mật   |   Liên kết đến bảng dữ liệu    |   Trao đổi link   |   Tìm kiếm theo nhà sản xuất
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com