| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
LPC55S0X bảng dữ liệu(PDF) 43 Page - NXP Semiconductors |
|
|
|||||||||||||||||||||||||||||
LPC55S0X bảng dữ liệu(HTML) 43 Page - NXP Semiconductors |
|
43 / 119 page ![]() LPC55S0x/LPC550x All information provided in this document is subject to legal disclaimers. © NXP Semiconductors N.V. 2023. All rights reserved. Product data sheet Rev. 1.4 — 14 April 2023 43 of 124 NXP Semiconductors LPC55S0x/LPC550x 32-bit ARM Cortex-M33 microcontroller 7.19 RAM configuration Table 9 describes the RAM configuration. 7.20 System control 7.20.1 Clock sources The LPC55S0x/LPC550x supports 2 external and 3 internal clock sources: • Internal Free Running Oscillator (FRO). This oscillator provides a selectable 96 MHz output, and a 12 MHz output (divided down from the selected higher frequency) that can be used as a system clock. The FRO is trimmed to +/- 1% accuracy over the entire voltage and 0 C to 85 C. The FRO is trimmed to +/- 2% accuracy over the entire voltage and -40 C to 105 C. The FRO 12 MHz oscillator provides the default clock at reset and provides a clean system clock shortly after the supply pins reach operating voltage. • 32 kHz Internal Free Running Oscillator FRO. The FRO is trimmed to +/- 2% accuracy over the entire voltage and temperature range. • Internal low power oscillator (FRO 1 MHz). The FRO is trimmed to +/- 15% accuracy over the entire voltage and temperature range. • Crystal oscillator with an operating frequency of 16 MHz to 32 MHz. Option for external clock input (bypass mode) for clock frequencies of up to 25 MHz • Crystal oscillator with 32.768 kHz operating frequency. • Each crystal oscillator has one embedded capacitor bank, where each can be used as an integrated load capacitor for the crystal oscillators. Using APIs, the capacitor banks on each crystal pin can tune the frequency for crystals with a Capacitive Load (CL) leading to conserving board space and reducing costs. See: Section 13 “Application information”. 7.20.2 PLL (PLL0 and PLL1) PLL0 and PLL1 allows CPU operation up to the maximum CPU rate without the need for a high-frequency external clock. PLL0 and PLL1 can run from the internal FRO 12 MHz output, the external oscillator, internal FRO 1 MHz output, or the 32.768 kHz RTC oscillator. The system PLL accepts an input clock frequency in the range of 2 kHz - 150 MHz. The input frequency is multiplied up to a high frequency with a Current Controlled Oscillator (CCO). The PLL can be enabled or disabled by software. 7.20.3 Clock generation The system control block facilitates the clock generation. Many clocking variations are possible. Figure 6 gives an overview of potential clock options. Table 10 describes signals on the clocking diagram. The maximum clock frequency is 96 MHz. Table 9. RAM Configuration RAM Total RAM-X (KB) RAM0 (KB) RAM1 (KB) RAM2 (KB) RAM 3 (KB) 96 KB devices 16 32 16 16 16 80 KB devices 16 32 16 16 - 48 KB devices 16 32 - - - |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |