MIP SERIES HEAVY DUTY, MEDIA-ISOLATED PRESSURE TRANSDUCERS

MIP Series Heavy Duty, Media-Isolated Pressure Transducers Datasheet | sps.honeywell.com/ast |

2

TABLE 3. PERFORMANCE SPECIFICATIONS (AT 25°C [77°F] AND UNDER UNLESS OTHERWISE NOTED.)

CHARACTERISTIC

RATIOMETRIC OUTPUT

CURRENT OUTPUT

Total Error Band1

>10 bar or >150 psi: ±0.75 %FSS (-40°C to 125°C)

<10 bar or <150 psi: ±1.0 %FSS2 (-40°C to 125°C)

±1.0 %FSS (-20°C to 85°C)

±2.0 %FSS (-40°C to 125°C)

Operating temperature range

-40°C to 125°C [-40°F to 257°F]

Accuracy BFSL3

±0.15 %FSS

±0.25 %FSS

Long term stability (1000 hr, 25°C)

±0.25 %FSS

Typical output resolution

0.05 % Full Scale Pressure

Typical response time4

1 ms

2 ms

Startup time5

7 ms

EMC rating (CE Conformity):

surge immunity (all leads)

electrostatic discharge

radiated immunity

fast transient burst

immunity to conducted disturbances

radiated emissions

±1 kV line to ground per IEC 61000-4-5

±4 kV contact, ±8 kV air per IEC 61000-4-2

10 V/m (80 MHz to 1000 MHz) per IEC 61000-4-3

±1 kV per IEC 61000-4-4

3 V (150 kHz to 80 MHz) per IEC 61000-4-6

40 dBµV (30 MHz to 230 MHz), 47 dBµV (230 MHz to 1000 MHz) per CISPR 11

Radiated immunity

100 V/m (200 MHz to 2.5 GHz) per ISO 11452-2

100 V/m (300 MHz to 2.7 GHz) per ISO 11452-2

100 V/m (100 kHz to 400 MHz) per ISO 11452-5

Insulation resistance

>100 MΩ at 1k Vdc (60 s)

Dielectric strength

<1 mA at 500 Vac (60 s)

<1 mA at 1000 Vac (60 s)

Life

>10 million full scale pressure cycles

1

Total Error Band: The maximum deviation from the ideal transfer function over the entire compensated temperature and pressure range.

Includes all errors due to offset, full scale span, pressure non-linearity, pressure hysteresis, pressure non-repeatability, thermal effect on offset,

thermal effect on span, and thermal hysteresis (see Figure 5).

2

TEB: Above 100°C [212°F] for pressure ratings less than 4 bar [58 psi], TEB is ±1.5 %FSS for ratiometric outputs and 2.0 % FSS for other outputs.

3

Accuracy: The maximum deviation in output from a Best Fit Straight Line (BFSL) fitted to the output measured over the pressure range at 25°C

[77°F]. Includes all errors due to pressure non-linearity, pressure hysteresis, and pressure non-repeatability.

4

Response time: The time taken by the transducer to change output from 10 % to 90 % of full scale in response to a 0 % to 100 % full scale step

input pressure.

5

Startup time: The time needed to receive valid output after power up.

TABLE 2. ELECTRICAL SPECIFICATIONS (AT 25°C [77°F] AND UNDER UNLESS OTHERWISE NOTED.)

CHARACTERISTIC

RATIOMETRIC OUTPUT (AA)

CURRENT OUTPUT (CH)

Supply voltage (Vs)

5.0 Vdc ±0.25 Vdc

8 Vdc to 30 Vdc1

Output transfer function

10 % to 90 % of Vs

4 mA to 20 mA

Output load (pull up or pull down)

> 2 kΩ

(Vs - 8) x 50Ω2

Short circuit protection

yes

Current consumption

6.5 mA ±1 mA

_

Over/reverse voltage

±40 Vdc

±35 Vdc

1

Supply voltage: Must be de-rated to 8 Vdc to 25 Vdc for above 100°C to 125°C [212°F to 257°F].

2

Applies at 25°C [77°F]. See Figure 4 for Current Output Supply Voltage.

TABLE 4. ENVIRONMENTAL AND MECHANICAL SPECIFICATIONS

CHARACTERISTIC

PARAMETER

Shock

100 G per MIL-STD-202, Method 213, Cond. C (at 25°C [77°F])

Vibration

20 G sweep, 10 Hz to 2000 Hz (at 25°C [77°F])

Ingress protection:

Metri-Pack 150 versions

cable harness versions

IP65, IP67

IP65, IP67, IP69K

External freeze/thaw resistance

>6 cycles from -30°C to 50°C [-22°F to 122°F] (Metri-Pack 150 versions only)

Wetted materials:

port

diaphragm

external seal for ports

stainless steel 304L

stainless steel 316L

nitrile (-30°C to 100°C [-22°F to 212°F]) (other materials available)

Electrical connector material

PBT 30 %GF (UL V-0)

Cable material (jacket and insulation)

TPE (Thermoplastic Elastomer) flame retardant-type cable is FT1 rated per CSA

AWM-I-A/B-II-A/B specification, -40°C to 125°C [-40°F to 257°F], three 24 AWG wires.