TLP352,TLP352F

6

11.

11.

11.

11. Isolation Characteristics (Unless otherwise specified, T

Isolation Characteristics (Unless otherwise specified, T

Isolation Characteristics (Unless otherwise specified, T

Isolation Characteristics (Unless otherwise specified, Taaaa = 25

= 25

= 25

= 25 





))))

Characteristics

Total capacitance (input to output)

Isolation resistance

Isolation voltage

Symbol

CS

RS

BVS

Note

(Note 1)

(Note 1)

(Note 1)

Test Conditions

VS = 0 V, f = 1 MHz

VS = 500 V, R.H. ≤ 60 %

AC, 60 s

AC, 1 s in oil

DC, 60 s in oil

Min



1 × 1012

3750





Typ.

1.0

1014



10000

10000

Max











Unit

pF

Ω

Vrms

Vdc

Note 1: This device is considered as a two-terminal device: Pins 1, 2, 3 and 4 are shorted together, and pins 5, 6, 7

and 8 are shorted together.

12.

12.

12.

12. Switching Characteristics (Note) (Unless otherwise specified, T

Switching Characteristics (Note) (Unless otherwise specified, T

Switching Characteristics (Note) (Unless otherwise specified, T

Switching Characteristics (Note) (Unless otherwise specified, Taaaa = -40 to 125

= -40 to 125

= -40 to 125

= -40 to 125 





))))

Characteristics

Propagation delay time

(L/H)

Propagation delay time

(H/L)

Rise time

Fall time

Pulse width distortion

Propagation delay skew

(device to device)

Common-mode transient

immunity at output high

Common-mode transient

immunity at output low

Symbol

tpLH

tpHL

tr

tf

|tpHL-tpLH|

tpsk

CMH

CML

Note

(Note 1)

(Note 1)

(Note 1)

(Note 1)

(Note 1),

(Note 2)

(Note 3)

(Note 4)

Test

Circuit

Fig.

13.1.7

Fig.

13.1.8

Test Condition

IF = 0 → 5 mA, VCC = 30 V,

Rg = 20 Ω, Cg = 10 nF

IF = 5 → 0 mA, VCC = 30 V,

Rg = 20 Ω, Cg = 10 nF

IF = 0 → 5 mA, VCC = 30 V,

Rg = 20 Ω, Cg = 10 nF

IF = 5 → 0 mA, VCC = 30 V,

Rg = 20 Ω, Cg = 10 nF

IF = 0 ←→ 5 mA, VCC = 30 V,

Rg = 20 Ω, Cg = 10 nF

IF = 0 ←→ 5 mA, VCC = 30 V,

Rg = 20 Ω, Cg = 10 nF

VCM = 1000 Vp-p, IF = 5 mA,

VCC = 30 V, Ta = 25 ,

VO(min) = 26 V

VCM = 1000 Vp-p, IF = 0 mA,

VCC = 30 V, Ta = 25 ,

VO(max) = 1 V

Min

50

50







-80

±20

±20

Typ.

130

130

15

8





±25

±25

Max

200

200





50

80





Unit

ns

kV/µs

Note:

All typical values are at Ta = 25 .

Note 1: Input signal (f = 25 kHz, duty = 50 %, tr = tf = 5 ns or less).

CL is approximately 15 pF which includes probe and stray wiring capacitance.

Note 2: The propagation delay skew, tpsk, is equal to the magnitude of the worst-case difference in tpHL and/or tpLH

that will be seen between units at the same given conditions (supply voltage, input current, temperature, etc).

Note 3: CMH is the maximum rate of fall of the common mode voltage that can be sustained with the output voltage in

the logic high state (VO > 26 V).

Note 4: CML is the maximum rate of rise of the common mode voltage that can be sustained with the output voltage

in the logic low state (VO < 1 V).

2016-09-27

Rev.7.0

©2016 Toshiba Corporation