công cụ tìm kiếm bảng dữ liệu linh kiện điện tử
  Vietnamese  ▼
ALLDATASHEET.VN

X  

L99MOD50XP bảng dữ liệu(PDF) 28 Page - STMicroelectronics

tên linh kiện L99MOD50XP
Giải thích chi tiết về linh kiện  Multi-output driver for automotive applications
PDF  42 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
nhà sản xuất  STMICROELECTRONICS [STMicroelectronics]
Trang chủ  http://www.st.com
Logo STMICROELECTRONICS - STMicroelectronics

L99MOD50XP bảng dữ liệu(HTML) 28 Page - STMicroelectronics

Back Button L99MOD50XP Datasheet HTML 24Page - STMicroelectronics L99MOD50XP Datasheet HTML 25Page - STMicroelectronics L99MOD50XP Datasheet HTML 26Page - STMicroelectronics L99MOD50XP Datasheet HTML 27Page - STMicroelectronics L99MOD50XP Datasheet HTML 28Page - STMicroelectronics L99MOD50XP Datasheet HTML 29Page - STMicroelectronics L99MOD50XP Datasheet HTML 30Page - STMicroelectronics L99MOD50XP Datasheet HTML 31Page - STMicroelectronics L99MOD50XP Datasheet HTML 32Page - STMicroelectronics Next Button
Zoom Inzoom in Zoom Outzoom out
 28 / 42 page
background image
Functional description of the SPI
L99MOD50XP
28/42
DS12615 Rev 4
Description:
GL_ER: Global Error Flag. Failures of Bits 0-6 are always linked to the Global Error
Flag. This flag is generated by an OR combination of all failure events of the device. It
is reflected via the DO pin while CSN is held low and no clock signal is available. The
flag remains as long as CSN is low. This operation does not cause the Communication
Error bit in the <Global Status> to be set. The signal TW bit3 and OL bit1can be
masked.
CO_ER: Communication Error. If the number of clock pulses within the previous frame
is not 24 the frame is ignored and this bit is set.
C_RESET: Chip RESET. If a stuck at ‘1’ on input DI during any SPI frame occurs, or if a
Power On Reset (VCC monitor) occurs. C_RESET resets (‘1’) with any SPI command.
When C_RESET is active (‘0’), the Gate drivers are switched off (resistive path to
source).
After a startup of the circuit the C_RESET is active because of the POR pulse and the
Gate drivers are switched off. The Gate drivers can only be activated after the
C_RESET has been reset with a SPI command.
TSD: Thermal shutdown due to an internal sensor. All the gate drivers and the charge
pump are switched off (resistive path to source). The TSD bit has to be cleared through
a software reset to reactivate the gate drivers and the charge pump.
TW: Thermal Warning. This bit is maskable by configuration register.
UOV_OC: Logical OR among the filtered under-/over-voltage signals and over-current
signals.
OL: Open Load. Logical OR among the filtered under-current signals. This bit is
maskable by configuration register.
NR: Not Ready. After switching the device from standby mode to active mode an
internal timer is started to allow charge-pump to settle before the outputs can be
activated. This bit is cleared automatically after start up time has finished.
Figure 10. Global error flag definition



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42


bảng dữ liệu tải về

Go To PDF Page


Link URL



Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không?  [ DONATE ] 

Alldatasheet là   |   Quảng cáo   |   Liên lạc với chúng tôi   |   Chính sách bảo mật   |   Liên kết đến bảng dữ liệu    |   Trao đổi link   |   Tìm kiếm theo nhà sản xuất
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com