76232103 datasheet(18/70 Pages) TOSHIBA

18 / 70 page

– 18 –

Auto fine tuning (AFT)

If the signal frequency is unstable due to environmental

conditions, use auto fine tuning.

1 Select the position number where the channel you

want to fine-tune with CH s/t or the digit selection

and number buttons (-/--, 0~9).

Note

When the position is set to “AFT OFF” status, the “R”

mark appears to the left of the position number.

When the channel is set to “AFT ON” status,the

position number is displayed without the “R” mark.

2 Press MENU then < / > to highlight the “SETUPCH???? SET UP”

icon.

3 Press / to select“AFT”.Press < / > to select the

“ON” indication.

ASM

SKIP

OFF

[

< ] [ > ]

POSITION

P25

MEMORY

MFT

[

< ] [ > ]

AFT

SET UP

FUNC.

AUDIO

PICTURE

TIMER

????

SELECT

ADJUST

Notes

• When you operate MFT, AFT is switched “OFF”

automatically. If you switch on AFT after fine tuning with

MFT, MFT may be canceled.

• AFT may be set independently for each position.

To skip a position number

After presetting the channels, you may skip unnecessary

position numbers so that only the channels you want to watch

are selected using CH s/t.

1 First, select the position number to be skipped with

CH s/t or digit selection and number buttons (-/--,

0~9).

2 Highlight the “SETUPCH???? SET UP” icon and press / to

select “SKIP”.

ASM

SKIP

OFF

[

< ] [ > ]

POSITION

P12

MEMORY

MFT

[

< ] [ > ]

AFT

SET UP

FUNC.

AUDIO

PICTURE

TIMER

????

SELECT

ADJUST

3 Press < / > to set“SKIP”to“ON”.This completes the

setting for skipping the selected position number.

Notes

• When “SKIP” is set to “ON” for the selected position

number, a “ * ” mark appears to the left of the position

number.

The position number will then be skipped when you select

the position with the CH s/t buttons.

• If you want to restore a skipped position number, select it

using the -/-- and 0~9 buttons then switch the “SKIP” setting

to “OFF”.

Manual fine tuning (MFT)

The adjustments below are not necessary under normal

conditions. However, under some reception conditions, fine

tuning may be necessary to improve the picture quality. In

such cases, adjust the manual fine tuning (MFT).

1 Select the position number where the channel you

want to fine-tune with CH s/t or digit selection and

number buttons (-/--, 0~9).

2 Press MENU and then < / > to highlight the “SETUPCH???? SET

UP” icon.

3 Press / to select “MFT”.Press < / > to start fine

tuning. Press

< / > repeatedly until the best possible

picture and sound are obtained.

ASM

SKIP

OFF

[

< ] [ > ]

POSITION

P04

MEMORY

MFT

[

< ] [ > ]

AFT

SET UP

FUNC.

AUDIO

PICTURE

TIMER

????

SELECT

ADJUST

76232103 bảng dữ liệu(PDF) 18 Page - Toshiba Semiconductor

76232103 bảng dữ liệu(HTML) 18 Page - Toshiba Semiconductor

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70

bảng dữ liệu tải về

Link URL