| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
STM32L15XCC bảng dữ liệu(PDF) 74 Page - STMicroelectronics |
|
|
|||||||||||||||||||||||||||||
STM32L15XCC bảng dữ liệu(HTML) 74 Page - STMicroelectronics |
|
74 / 136 page ![]() Electrical characteristics STM32L151xC STM32L152xC 74/136 DocID022799 Rev 13 For CL1 and CL2, it is recommended to use high-quality external ceramic capacitors in the 5 pF to 25 pF range (typ.), designed for high-frequency applications, and selected to match the requirements of the crystal or resonator (see Figure 17). CL1 and CL2 are usually the same size. The crystal manufacturer typically specifies a load capacitance which is the series combination of CL1 and CL2. PCB and MCU pin capacitance must be included (10 pF can be used as a rough estimate of the combined pin and board capacitance) when sizing CL1 and CL2. Refer to the application note AN2867 “Oscillator design guide for ST microcontrollers” available from the ST website www.st.com. Table 29. HSE oscillator characteristics(1)(2) Symbol Parameter Conditions Min Typ Max Unit fOSC_IN Oscillator frequency - 1 24 MHz RF Feedback resistor - - 200 - k Ω C Recommended load capacitance versus equivalent serial resistance of the crystal (RS)(3) RS = 30 Ω -20 - pF IHSE HSE driving current VDD= 3.3 V, VIN = VSS with 30 pF load -- 3 mA IDD(HSE) HSE oscillator power consumption C = 20 pF fOSC = 16 MHz -- 2.5 (startup) 0.7 (stabilized) mA C = 10 pF fOSC = 16 MHz -- 2.5 (startup) 0.46 (stabilized) gm Oscillator transconductance Startup 3.5 - - mA /V tSU(HSE)(4) Startup time VDD is stabilized - 1 - ms 1. Resonator characteristics given by the crystal/ceramic resonator manufacturer. 2. Guaranteed by characterization results. 3. The relatively low value of the RF resistor offers a good protection against issues resulting from use in a humid environment, due to the induced leakage and the bias condition change. However, it is recommended to take this point into account if the MCU is used in tough humidity conditions. 4. tSU(HSE) is the startup time measured from the moment it is enabled (by software) to a stabilized 8 MHz oscillation is reached. This value is measured for a standard crystal resonator and it can vary significantly with the crystal manufacturer. |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |