ADF4212LBRU datasheet(10/20 Pages) AD

10 / 20 page

REV. 0

ADF4212L

–10–

Prescaler (P/P + 1)

The dual-modulus prescaler (P/P + 1), along with the A and B

counters, enables the large division ratio N, to be realized

(N = PB + A). The dual-modulus prescaler, operating at CML

levels, takes the clock from the RF/IF input stage and divides it

down to a manageable frequency for the CMOS A and B

counters in the RF and IF sections. The prescaler in both

sections is programmable. It can be set in software to 8/9, 16/17,

32/33, or 64/65. See Table IV and Table VI. It is based on a

synchronous 4/5 core.

RF/IF A and B Counters

The A and B CMOS counters combine with the dual modulus

prescaler to allow a wide ranging division ratio in the PLL feed-

back counter. The counters are specified to work when the

prescaler output is 200 MHz or less. Typically, they will work

with 250 MHz output from the prescaler. Thus, with an RF

input frequency of 2.5 GHz, a prescaler value of 16/17 is valid,

but a value of 8/9 is not valid.

Pulse Swallow Function

The A and B counters, in conjunction with the dual modulus

prescaler, make it possible to generate output frequencies that

are spaced only by the Reference Frequency divided by R. The

equation for the VCO frequency is as follows:

VCO

REFIN

=×

() +

[]×

fVCO = Output frequency of external voltage controlled

oscillator (VCO)

Preset modulus of dual modulus prescaler (8/9, 16/17, and so on)

Preset divide ratio of binary 13-bit counter (3 to 8191)

Preset divide ratio of binary 6-bit swallow counter (0 to 63)

fREFIN =External reference frequency oscillator

=Preset divide ratio of binary 14-bit programmable

reference counter (1 to 16383)

TO PFD

N = BP + A

LOAD

MODULUS

CONTROL

FROM RF

INPUT STAGE

12-BIT B

COUNTER

6-BIT A

COUNTER

PRESCALER

P/P+1

Figure 4. RF/IF A and B Counters

RF/IF R Counter

The 14-bit RF/IF R counter allows the input reference fre-

quency to be divided down to produce the input clock to the

phase frequency detector (PFD). Division ratios from 1 to

16,383 are allowed.

Phase Frequency Detector (PFD) and Charge Pump

The PFD takes inputs from the R counter and N counter and

produces an output proportional to the phase and frequency

difference between them. Figure 5 is a simplified schematic.

The PFD includes a fixed delay element that sets the width

of the antibacklash pulse. This is typically 3 ns. This pulse ensures

that there is no dead zone in the PFD transfer function and gives a

consistent reference spur level.

CLR1

DELAY

CLR2

DOWN

+IN

–IN

CHARGE

PUMP

Figure 5. RF/IF PFD Simplified Schematic

MUXOUT and Lock Detect

The output multiplexer on the ADF4212L allows the user to

access various internal points on the chip. The state of MUX-

OUT is controlled by P3, P4, P11, and P12. See Table III and

Table V. Figure 6 shows the MUXOUT section in block dia-

gram form.

Lock Detect

MUXOUT can be programmed for two types of lock detect:

digital lock detect and analog lock detect. Digital Lock Detect is

active high. It is set high when the phase error on three con-

secutive Phase Detector cycles is less than 15 ns. It will stay set

high until a phase error of greater than 25 ns is detected on any

subsequent PD cycle.

The N-channel open-drain Analog Lock Detect should be oper-

ated with an external pull-up resistor of 10 k

Ω nominal. When

lock has been detected, it is high with narrow low going pulses.

IF ANALOG LOCK DETECT

IF R COUNTER OUTPUT

IF N COUNTER OUTPUT

IF/RF ANALOG LOCK DETECT

RF R COUNTER OUTPUT

RF N COUNTER OUTPUT

RF ANALOG LOCK DETECT

MUX

CONTROL

MUXOUT

DVDD

DGND

Figure 6. MUXOUT Schematic

ADF4212LBRU bảng dữ liệu(PDF) 10 Page - Analog Devices

ADF4212LBRU bảng dữ liệu(HTML) 10 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

bảng dữ liệu tải về

Link URL