R7K4FE-6-DC16-R datasheet(2/7 Pages) MSYSTEM

2 / 7 page

MODEL: R7K4FE-6-DC16

R7K4FE-6-DC16 SPECIFICATIONS

ES-7778-A Rev.2 Page 2/7

https://www.m-system.co.jp/

Data: RTU (Binary)

Max. number of socket connections: 2

Transmission media: 10BASE-T (STP, Category 5) 100BASE-

TX (STP, Category 5e)

Max. length of fieldbus segment: 100 meters

IP address: 192.168.0.1 (factory setting);

Selectable with PC Configurator Software (model: R7CFG)

Port No.: 502

Ethernet indicator LED: Link, Link100, COL

(Refer to the insruction manual)

OUTPUT SPECIFICATIONS

Common: 1 common per 1 point (16 points)

Maximum load current: 2.0 A per point

Maximum outputs applicable at once: No limit (at 24 V DC)

Output supply voltage/current: 24 V DC ±10 %/ ≥ 120 mA

Rated load: 250 V AC @ 2A, 30 V DC @ 2A

Maximum switching voltage: 250 V AC, 30 V DC

Maximum switching power: 500 VA (AC), 60 W (DC)

Minimum applicable load: 5 V DC @ 1 mA

Mechanical life: 2 × 107 cycles (300 cycles per min.)

When driving an inductive load, external contact protection

and noise quenching recommended.

ON delay time: ≤ 10 msec.

OFF delay time: ≤ 10 msec.

INSTALLATION

Current consumption

•DC: Approx. 130 mA (contact output load charge is not

included)

Operating temperature: -10 to +55°C (14 to 131°F)

Storage temperature: -20 to +65°C (-4 to +149°F)

Operating humidity: 30 to 90 %RH (non-condensing)

Atmosphere: No corrosive gas or heavy dust

Mounting: Surface or DIN rail (35 mm rail)

Weight: 330 g (0.73 lb)

PERFORMANCE

Insulation resistance: ≥ 100 MΩ with 500 V DC

Dielectric strength: 1500 V AC @ 1 minute

(output 0 to output 1 to output 2 to output 3 to output 4 to

output 5 to output 6 to output 7 to output 8 to output 9 to

output 10 to output 11 to output 12 to output 13 to output

14 to output 15 to Ethernet or FE to power)

STANDARDS & APPROVALS

EU conformity:

EMC Directive

EMI EN 61000-6-4

EMS EN 61000-6-2

Low Voltage Directive

EN 61010-1, EN 61010-2-201

Measurement Category II (output)

Pollution Degree 2

Output to power: Basic insulation (250 V)

RoHS Directive

PC CONFIGURATOR

The following parameters can be set with using PC

Configurator Software (model: R7CFG)

Refer to the users manual for the R7CFG for detailed

operation of the software program.

PARAMETER

SETTING RANGE

DEFAULT

SETTING

IP Adress

0.0.0.0ー

255.255.255.255

192.168.0.1

Subnet Mask

0.0.0.0ー

255.255.255.255

255.255.255.0

Linger Time

0ー3276.7（sec.） 180.0（sec.）

Time Out

0ー3276.7（sec.） 3.0（sec.）

R7K4FE-6-DC16-R bảng dữ liệu(PDF) 2 Page - M-System Co.,Ltd.

R7K4FE-6-DC16-R bảng dữ liệu(HTML) 2 Page - M-System Co.,Ltd.

Html Pages

1 2 3 4 5 6 7

bảng dữ liệu tải về

Link URL