| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
MCP39F511A bảng dữ liệu(PDF) 36 Page - Microchip Technology |
|
|
|||||||||||||||||||||||||||||
MCP39F511A bảng dữ liệu(HTML) 36 Page - Microchip Technology |
|
36 / 68 page ![]() MCP39F511A DS20006044A-page 36 2018 Microchip Technology Inc. bit 15-13 UART<2:0>: UART Baud Rate bits (Note 1) 111 = 1200 110 = 2400 101 = 4800 100 = 9600 (Default) 011 = 19200 010 = 38400 001 = 57600 000 = 115200 bit 12 ZCD_INV: Zero Crossing Detection Output Inverse 1 = ZCD is inverted 0 = ZCD is not inverted (Default) bit 11 ZCD_PULS: Zero Crossing Detection Pulse mode 1 = ZCD output is 100 µs pulses on zero crossings 0 = ZCD Output changes logic state on zero crossings (Default) bit 10 ZCD_OUTPUT_DIS: Disable the Zero Crossing output pin 1 = ZCD output is disabled 0 = ZCD output is enabled (Default) bit 9 Unimplemented: Read as ‘0’ bit 8 SINGLE_WIRE: Single-Wire Enable bit 1 = Single-wire transmission is enabled 0 = Single-wire transmission is disabled (Default) bit 7 TEMPCOMP: Temperature-Compensation Enable bit 1 = Temperature compensation is enabled 0 = Temperature compensation is disabled (Default) bit 6-5 RESET <1:0>: Reset mode setting for ADCs 11 = Both I1 and V1 are in Reset mode 10 = V1 ADC is in Reset mode 01 = I1 ADC is in Reset mode 00 = Neither ADC is in Reset mode (Default) bit 4-3 SHUTDOWN <1:0>: Shutdown mode setting for ADCs 11 = Both I1 and V1 are in Shutdown 10 = V1 ADC is in Shutdown 01 = I1 ADC is in Shutdown 00 = Neither ADC is in Shutdown (Default) bit 2 VREFEXT: Internal Voltage Reference Shutdown Control 1 = Internal Voltage Reference Disabled 0 = Internal Voltage Reference Enabled (Default) bit 1 PWM_CNTRL: PWM Control 1 = PWM is turned on 0 = PWM is turned off (Default) bit 0 ENRG_CNTRL: Energy Accumulation Control bit 1 = Energy is ON and all registers are accumulating 0 = Energy accumulation is turned off and all energy accumulation registers are reset to 0 (Default) Note 1: The baud rate is only changed at system power-up, so a Save To Flash command is required after changing the baud rate. REGISTER 6-2: SYSTEM CONFIGURATION REGISTER (CONTINUED) |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |