| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
FXPS7115D4 bảng dữ liệu(PDF) 21 Page - NXP Semiconductors |
|
|
|||||||||||||||||||||||||||||
FXPS7115D4 bảng dữ liệu(HTML) 21 Page - NXP Semiconductors |
|
21 / 72 page ![]() NXP Semiconductors FXPS7115D4 Digital absolute pressure sensor, 40 kPa to 115 kPa FXPS7115D4 All information provided in this document is subject to legal disclaimers. © NXP B.V. 2019. All rights reserved. Product data sheet Rev. 3 — 5 December 2019 21 / 72 7.5.3 Command summary 7.5.3.1 Register read command The device supports a register read command. The register read command uses the upper 7 bits of the addresses defined in Section 7.6 "User-accessible data array" to address 8-bit registers in the register map. The response to a register read command is shown in Section 7.5.3.1.2 "Register read response message format". The response is transmitted on the next SPI message if and only if all of the following conditions are met: • No SPI error is detected (see Section 7.5.5.3 "SPI error" ) • No MISO error is detected (see Section 7.5.5.4 "SPI data output verification error") If these conditions are met, the device responds to the register read request as shown in Section 7.5.3.1.2 "Register read response message format". Otherwise, the device responds with the error response as defined in Section 7.5.5.2 "Error responses". The register read response includes the register contents at the rising edge of SS_B for the register read command. 7.5.3.1.1 Register read command message format Table 12. Register read command message format MSB: bit 31; LSB: bit 0 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Register access command Command C[3:0] Fixed bits: must = 0h Register address Register data 8-bit CRC 1 1 0 0 0 0 0 0 RA[7:1] RA[0] 0 0 0 0 0 0 0 0 CRC[7:0] Table 13. Register read command message bit field descriptions Bit field Definition C[3:0] Register read command = '1100' RA[7:0] RA[7:1] contains the word address of the register to be read. CRC[7:0] Read CRC Section 7.5.3.1.2 Register read response message format Table 14. Register read response message format MSB: bit 31; LSB: bit 0 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Register access command Command C[0], [3:1] Basic Status Unused Data 0h Register data: contents of RA[7:1] high byte Register data: contents of RA[7:1] low byte 8-bit CRC 0 1 1 0 ST[1:0] 0 0 RD[15:8] RD[7:0] CRC[7:0] |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |