Specifications

Supply Voltage

10 V dc to 30 V dc for ambient temperature ≤ 55 °C

10 V dc to 24 V dc for ambient temperature > 55 °C

Supply Current (Exclusive of Load Current)

All models except FF IR: < 16 mA

FF IR models: < 25 mA

Output Protection Circuitry

Protected against false pulse on power-up and continuous short

circuit of outputs. Short circuit protection at elevated temperature

may require a power cycle to reset.

Supply Protection Circuitry

Protected against reverse polarity and transient voltages

Output Rating

≤ 50 mA total current for ambient temperatures > 55 °C

≤ 100 mA total current through both outputs ≤ 55 °C

OFF-State Leakage Current: < 50 µA at 30 V dc

ON-State Saturation Voltage: < 1.5 V at 10 mA; < 3.0 V at 100 mA

Output Configuration

Complementary PNP or NPN by model number

Emitter LED

Visible Red on most models

Infrared 850 nm on select fixed-field models to provide higher

excess gain on blue and green targets

Output Response Time

Response is independent of signal strength

Opposed models: 1.5 milliseconds ON, 1 millisecond OFF

Polarized Retro, and Diffuse models: 1.5 milliseconds ON, 0.75

milliseconds OFF

Fixed Field models: 2 milliseconds ON, 2 milliseconds OFF

Delay on Power-up: 100 milliseconds; outputs do not conduct

during this time

Repeatability

Repeatability is independent of signal strength

Opposed models: 300 microseconds

Retro, Polarized Retro, and Diffuse models: 100 microseconds

Fixed Field models: 200 microseconds

Adjustments

Diffuse (DL, DS), Emitter (ES), Receiver (RS), Polarized

Retroreflective (LPC) models: Single turn sensitivity (gain)

adjustment potentiometer

Emitter Beam Inhibit (EJ) models: Tie black wire to 10 to 30 V dc for

beam inhibit

Construction

Housing, M12 QD, and cover: Black or Yellow PBT polyester

Indicator light pipes: Translucent white PMMA (acrylic)

Indicator cover and gain pot driver: PBT polyester

Front window: PMMA

Indicators

Two LEDs (1 green, 1 amber)

Green Solid: Indicates power applied and sensor ready

Green flashing: Indicates marginal sensing signal

Amber solid: Indicates Pin-4 (black wire) conducting

Vibration and Mechanical Shock

All models meet Mil. Std. 202G requirements. Method 201A

(Vibration; frequency 10 to 60 Hz, max., double amplitude 0.06 in

acceleration 10G). Method 213B conditions H&I (Shock: 75G with

unit operating; 100G for non-operation)

Operating Conditions

–40 °C to +70 °C (–40 °F to +158 °F)

95% at +50 °C maximum relative humidity (non-condensing)

Environmental Rating

IEC IP67 per IEC60529

IEC IP68 per IEC60529

DIN IP69K

Certifications

Industrial

Control

Equipment

3TJJ

Class 2 power

UL Environmental Rating: Type 1

Chemical compatibility certified

ECOLAB is a registered trademark of Ecolab USA Inc. All rights

reserved.

Required Overcurrent Protection

WARNING: Electrical connections must be

made by qualified personnel in

accordance with local and national

electrical codes and regulations.

Overcurrent protection is required to be provided by end product

application per the supplied table.

Overcurrent protection may be provided with external fusing or via

Current Limiting, Class 2 Power Supply.

Supply wiring leads < 24 AWG shall not be spliced.

For additional product support, go to

www.bannerengineering.com.

Supply Wiring

(AWG)

Required Overcurrent Protection (Amps)

20

5.0

22

3.0

24

2.0

26

1.0

28

0.8

30

0.5

T18-2 Epoxy Encapsulated Right-Angle Sensor

P/N 201875 Rev. C

www.bannerengineering.com - Tel: +1-763-544-3164

3