AM5728 datasheet(12/415 Pages) TI1

12 / 415 page

AM5729, AM5728, AM5726

SPRS953F – DECEMBER 2015 – REVISED MAY 2019

www.ti.com

Submit Documentation Feedback

Product Folder Links: AM5729 AM5728 AM5726

Terminal Configuration and Functions

An empty box means Not Applicable.

NOTE

For programmable buffer strength:

–

The default value is given in Table 4-2.

–

A note describes all possible values according to the selected muxmode.

14. PULLUP / PULLDOWN TYPE: Denotes the presence of an internal pullup or pulldown resistor.

Pullup and pulldown resistors can be enabled or disabled via software.

–

PU: Internal pullup

–

PD: Internal pulldown

–

PU/PD: Internal pullup and pulldown

–

PUx/PDy: Programmable internal pullup and pulldown

–

PDy: Programmable internal pulldown

–

An empty box means No pull

15. DSIS: The deselected input state (DSIS) indicates the state driven on the peripheral input (logic "0",

logic "1", or "PIN" level) when the peripheral pin function is not selected by any of the PINCNTLx

registers.

–

0: Logic 0 driven on the peripheral's input signal port.

–

1: Logic 1 driven on the peripheral's input signal port.

–

blank: Pin state driven on the peripheral's input signal port.

NOTE

Configuring two pins to the same input signal is not supported as it can yield unexpected

results. This can be easily prevented with the proper software configuration (Hi-Z mode is not

an input signal).

NOTE

When a pad is set into a multiplexing mode which is not defined by pin multiplexing, that

pad’s behavior is undefined. This should be avoided.

CAUTION

Not all exposed peripherals are supported on all AM572x devices. For

peripherals supported on specific device from AM572x family of products refer

to Table 3-1, Device Comparison Table.

NOTE

Some of the DDR1 and DDR2 signals have an additional state change at the release of porz.

The state that the signals change to at the release of porz is as follows:

drive 0 (OFF) for: ddr1_csn0, ddr1_ck, ddr1_nck, ddr1_casn, ddr1_rasn, ddr1_wen,

ddr1_ba[2:0], ddr1_a[15:0], ddr2_csn0, ddr2_ck, ddr2_nck, ddr2_casn, ddr2_rasn, ddr2_wen,

ddr2_ba[2:0], ddr2_a[15:0].

OFF for: ddr1_ecc_d[7:0], ddr1_dqm[3:0], ddr1_dqm_ecc, ddr1_dqs[3:0], ddr1_dqsn[3:0],

ddr1_dqs_ecc, ddr1_dqsn_ecc, ddr1_d[31:0], ddr2_dqm[3:0], ddr2_dqs[3:0], ddr2_dqsn[3:0],

ddr2_d[31:0].

AM5728 bảng dữ liệu(PDF) 12 Page - Texas Instruments

AM5728 bảng dữ liệu(HTML) 12 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL