PI74FCT521 datasheet(4/4 Pages) PERICOM

4 / 4 page

PI74FCT521T

8-BIT IDENTITY COMPARATOR

PS2019A 03/11/96

12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012

Switching Characteristics over Operating Range

521T

521AT

521BT

521CT

521DT

Com.

Parameters

Description

Conditions(1)

Min

Max

Min

Max

Min

Max

Min

Max

Min

Max

Unit

tPLH

Propagation Delay

CL = 50 pF

1.5

10.0

1.5

7.2

1.5

5.5

1.5

4.5

1.5

4.2

tPHL

AN or BN to OA=B

RL = 500

Ω

tPLH

Propagation Delay

1.5

9.0

1.5

6.0

1.5

4.6

1.5

4.1

1.5

3.8

tPHL

IA=B to OA=B

Power Supply Characteristics

Parameters Description

Test Conditions

(1)

Min.

Typ

(2)

Max.

Units

ICC

Quiescent Power

VCC = Max.

VIN = GND or VCC

0.1

500

µA

Supply Current

∆ICC

Supply Current per

VCC = Max.

VIN = 3.4V

(3)

0.5

2.0

Input @ TTL HIGH

ICCD

Supply Current per

VCC = Max.,

VIN = VCC

0.15

0.25

mA/

Input per MHz

(4)

Outputs Open

VIN = GND

MHz

One Input Toggling

50% Duty Cycle

Total Power Supply

VCC = Max.,

VIN = VCC

1.5

3.5

(5)

Current

(6)

Outputs Open

VIN = GND

fI = 10 MHZ

VIN = 3.4V

1.8

4.5

(5)

50% Duty Cycle

VIN = GND

One Bit Toggling

Notes:

1. For conditions shown as Max. or Min., use appropriate value specified under Electrical Characteristics for the applicable device.

2. Typical values are at Vcc = 5.0V, +25°C ambient.

3. Per TTL driven input (VIN = 3.4V); all other inputs at Vcc or GND.

4. This parameter is not directly testable, but is derived for use in Total Power Supply Calculations.

5. Values for these conditions are examples of the Icc formula. These limits are guaranteed but not tested.

6. IC =IQUIESCENT + IINPUTS + IDYNAMIC

IC = ICC +

∆ICC DHNT + ICCD (fCP/2 + fINI)

ICC = Quiescent Current

∆ICC = Power Supply Current for a TTL High Input (VIN = 3.4V)

DH = Duty Cycle for TTL Inputs High

NT = Number of TTL Inputs at DH

ICCD = Dynamic Current Caused by an Input Transition Pair (HLH or LHL)

fCP = Clock Frequency for Register Devices (Zero for Non-Register Devices)

fI = Input Frequency

NI = Number of Inputs at fI

All currents are in milliamps and all frequencies are in megahertz.

Notes:

1. See Test Circuit and Waveforms

2. Minimum limits are guaranteed but not tested on Propagation Delays.

Pericom Semiconductor Corporation

2380 Bering Drive • San Jose, CA 95131 • 1-800-435-2336 • Fax (408) 435-1100 • http://www.pericom.com

PI74FCT521 bảng dữ liệu(PDF) 4 Page - Pericom Semiconductor Corporation

PI74FCT521 bảng dữ liệu(HTML) 4 Page - Pericom Semiconductor Corporation

Html Pages

1 2 3 4

bảng dữ liệu tải về

Link URL