The Length Sensor Hinge Clamp Assembly provides an easy method for

attachment and mounting of the Length Sensors and LSCB1 Conversion

Bracket. The removable top on the solid zinc LSAHC mounting block

allows quick installation of the Length Sensor handle tube and provides

secure clamping retention. The mounting block pivots freely in zinc right

angle brackets to allow mounting the assembly via clearance holes for 1/4"

dia. bolts.

The lock washers must be used as indicated (between the bolt head and

the top clamp piece). Assemble the top clamp piece as follows.

1. Tighten both bolts so that the top clamp half draws down evenly on

the sensor tube.

2. Tighten the bolts until both lock washers are flat.

ORDERING INFORMATION

.88

(22.4)

2.9

(73.7)

3.4

(86.4)

2.5 (63.5)

1.25

(31.8)

.25 (6.3)

Lock washers (2) must be

installed between bolt heads

and top clamp piece.

E-clip retaining ring (2)

must be installed in slots.

5.70 (144.8)

4.50 (114.3)

(50.8)

(38.1)

0.75

0.75 (19.0)

4X Ø 0.31 (7.9)

2.00

1.50

(19.0)

SINGLE WHEEL

2.93 (74.4)

DUAL WHEEL 4 (101.6)

(21.6)

.85

.88 (22.4)

WHEEL

RADIUS

1.9

(48.3)

6.9

(175.3)

FRONT

VIEW

TOP

VIEW

DIMENSIONS In inches (mm)

CAUTION: Downward tension

on signal cable can cause

wheel(s) to lift. Make sure

cable is clamped to

machine frame near

encoder and allow slack.

NOTE: The weight at the

Length Sensor unit

provides sufficient traction

for accurate operation

when mounted as shown,

with arm angle from

horizontal not exceeding

±30°, and with hinge clamp

toward the far extreme of

the extension arm.

Length Sensors should be mounted so measuring

wheel(s) contact ribbon, strip or web as it passes over

a roller. As an alternative, wheel(s) can be driven by

roller surface next to material being measured.

MODEL NO.

DESCRIPTION

PART NUMBER

LSAHC

LSAHC001

Length Sensor Hinge Clamp Assembly

MODEL LSAHC - LENGTH SENSOR HINGE CLAMP ASSEMBLY

Note: After installation of measuring wheels, ensure guards,shields or other

devices are in place to protect personnel from rotating equipment.

WHEEL CODE

CIRCUMFERENCE

TOLERANCE

PART NUMBER

1 foot (1/3 yd)

±0.35%

WF1000OK

OK

1/3 meter

±0.30%

WM0333OK

4/10ths yard

±0.30%

WY0400OK

4/10ths meter

±0.30%

WM0400OK

BK (Balanced)

1 foot (1/3 yd)

±0.35%

WF1000BK

Replacement Tires

for

OR Wheels

1 foot (1/3 yd)

TORF1000

1/3 meter

TORM0333

4/10ths yard

TORY0400

4/10ths meter

TORM0400

TOLERANCE

WHEEL CODE CIRCUMFERENCE

PART NUMBER

1 foot (1/3 yd)

±0.40%

WF1000OR

OR

1/3 meter

±0.40%

WM0333OR

4/10ths yard

±0.40%

WY0400OR

4/10ths meter

±0.40%

WM0400OR

1 foot (1/3 yd)

±0.35%

WF1000OF

OF

1/3 meter

±0.30%

WM0333OF

4/10ths yard

±0.30%

WY0400OF

4/10ths meter

±0.30%

WM0400OF

BF (Balanced)

1 foot (1/3 yd)

±0.40%

WF1000BF

WHEELS & REPLACEMENT TIRES FOR CODE OR WHEELS

ORDERING INFORMATION

Model ZGH Shown

Model ZFH Shown

Red Lion Controls

Headquarters

20 Willow Springs Circle

York PA 17406

Tel +1 (717) 767-6511

Fax +1 (717) 764-0839

Red Lion Controls

China

Unit 302, XinAn Plaza

Building 13, No.99 Tianzhou Road

ShangHai, P.R. China 200223

Tel +86 21 6113 3688

Fax +86 21 6113 3683

Red Lion Controls

Europe

Softwareweg 9

NL - 3821 BN Amersfoort

Tel +31 (0) 334 723 225

Fax +31 (0) 334 893 793

Red Lion Controls

India

201-B, 2nd Floor, Park Centra

Opp 32 Mile Stone, Sector-30

Gurgaon-122002 Haryana, India

Tel +91 984 487 0503