| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
RT8494GS bảng dữ liệu(PDF) 14 Page - Richtek Technology Corporation |
|
|
|||||||||||||||||||||||||||||
RT8494GS bảng dữ liệu(HTML) 14 Page - Richtek Technology Corporation |
|
14 / 17 page ![]() RT8494 14 DS8494-01 November 2015 www.richtek.com © Copyright 2015 Richtek Technology Corporation. All rights reserved. is a registered trademark of Richtek Technology Corporation. For LED applications, the equivalent resistance of the LED is typically low and the output filter capacitor should be sized to attenuate the current ripple. Use of X7R type ceramic capacitors is recommended. Lower operating frequencies will require proportionately higher capacitor values. Thermal Considerations For continuous operation, do not exceed absolute maximum junction temperature. The maximum power dissipation depends on the thermal resistance of the IC package, PCB layout, rate of surrounding airflow, and difference between junction and ambient temperature. The maximum power dissipation can be calculated by the following formula : PD(MAX) = (TJ(MAX) − TA) / θJA where TJ(MAX) is the maximum junction temperature, TAis the ambient temperature, and θJAis the junction to ambient thermal resistance. For recommended operating condition specifications, the maximum junction temperature is 125 °C. The junction to ambient thermal resistance, θJA, is layout dependent. For SOP-14 packages, the thermal resistance, θJA, is 113.9 °C/W on a standard JEDEC 51-7 four-layer thermal test board. The maximum power dissipation at TA = 25 °C can be calculated by the following formula : PD(MAX) = (125 °C − 25°C) / (113.9°C/W) = 0.87W for SOP-14 package The maximum power dissipation depends on the operating ambient temperature for fixed TJ(MAX) and thermal resistance, θJA. The derating curves in Figure 6 allow the designer to see the effect of rising ambient temperature on the maximum power dissipation. OUT OUT OUT IN RIPPLE SW IV C VV f Schottky Diode Selection The Schottky diode, with their low forward voltage drop and fast switching speed, is necessary for the RT8494 applications. In addition, power dissipation, reverse voltage rating and pulsating peak current are the important parameters for the Schottky diode selection. Choose a suitable Schottky diode whose reverse voltage rating is greater than maximum output voltage. The diode’s average current rating must exceed the average output current. The diode conducts current only when the power switch is turned off (typically less than 50% duty cycle). If using the PWM feature for dimming, it is important to consider diode leakage, which increases with the temperature, from the output during the PWM low interval. Therefore, choose the Schottky diode with sufficiently low leakage current. Capacitor Selection The input capacitor reduces current spikes from the input supply and minimizes noise injection to the converter. For most the RT8494 applications, a 10 μF ceramic capacitor is sufficient. A value higher or lower may be used depending on the noise level from the input supply and the input current to the converter. In Boost application, the output capacitor is typically a ceramic capacitor and is selected based on the output voltage ripple requirements. The minimum value of the output capacitor COUT is approximately given by the following equation : SW OCP Current Limlit Threshold Minimum Value R I where IOCP is about 1.33 to 1.5 times of inductor peak current IPEAK. The placement of RSW should be close to the source of the N-MOSFET and the IC GND of the RT8494. The ISW pin input to RT8494 should be a Kelvin sense connection to the positive terminal of RSW. switch current to drive the application without exceeding the current limit threshold set by the ISW pin sense threshold of RT8494. The ISW sense resistor value can be calculated according to the formula below : |
|
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |