| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
ICS84314 bảng dữ liệu(PDF) 9 Page - Integrated Circuit Systems |
|
|
|||||||||||||||||||||||||||||
ICS84314 bảng dữ liệu(HTML) 9 Page - Integrated Circuit Systems |
|
9 / 18 page ![]() 84314AY www.icst.com/products/hiperclocks.html REV. C JANUARY 27, 2005 9 Integrated Circuit Systems, Inc. ICS84314 350MHZ, CRYSTAL-TO-3.3V/2.5V LVPECL FREQUENCY SYNTHESIZER W/FANOUT BUFFER V CC - 2V 50 Ω 50 Ω RTT Z o = 50Ω Z o = 50Ω FOUT FIN RTT = Z o 1 ((V OH + VOL) / (VCC – 2)) – 2 3.3V 125 Ω 125 Ω 84 Ω 84 Ω Z o = 50Ω Z o = 50Ω FOUT FIN The clock layout topology shown below is a typical termina- tion for LVPECL outputs. The two different layouts mentioned are recommended only as guidelines. FOUT and nFOUT are low impedance follower outputs that generate ECL/LVPECL compatible outputs.Therefore, terminat- ing resistors (DC current path to ground) or current sources must be used for functionality. These outputs are designed to FIGURE 3B. LVPECL OUTPUT TERMINATION FIGURE 3A. LVPECL OUTPUT TERMINATION drive 50 Ω transmission lines. Matched impedance techniques should be used to maximize operating frequency and minimize signal distortion. Figures 3A and 3B show two different layouts which are recommended only as guidelines. Other suitable clock layouts may exist and it would be recommended that the board designers simulate to guarantee compatibility across all printed circuit and clock component process variations. TERMINATION FOR 3.3V LVPECL OUTPUTS APPLICATION INFORMATION As in any high speed analog circuitry, the power supply pins are vulnerable to random noise. The ICS84314 provides sepa- rate power supplies to isolate any high switching noise from the outputs to the internal PLL. V CC, VCCA, and VCCO should be individually connected to the power supply plane through vias, and bypass capacitors should be used for each pin. To achieve optimum jitter performance, power supply isolation is required. Figure 2 illustrates how a 10 Ω resistor along with a 10µF and a .01µF bypass capacitor should be connected to each V CCA pin. POWER SUPPLY FILTERING TECHNIQUES FIGURE 2. POWER SUPPLY FILTERING 10 Ω V CCA 10 µF .01 µF 3.3V .01 µF V CC |
|
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |