LQFP144 datasheet(61/133 Pages) STMICROELECTRONICS

61 / 133 page

DocID15131 Rev 9

61/133

SPC560B54x/6x

Electrical characteristics

132

4.5

Thermal characteristics

4.5.1

External ballast resistor recommendations

External ballast resistor on VDD_BV pin helps in reducing the overall power dissipation inside

the device. This resistor is required only when maximum power consumption exceeds the

limit imposed by package thermal characteristics.

As stated in Table 15 LQFP thermal characteristics, considering a thermal resistance of

LQFP144 as 48.3 °C/W, at ambient temperature TA = 125 °C, the junction temperature Tj

will cross 150 °C if the total power dissipation is greater than (150 – 125)/48.3 = 517 mW.

Therefore, the total device current IDDMAX at 125 °C/5.5 V must not exceed 94.1 mA (i.e.,

PD/VDD). Assuming an average IDD(VDD_HV) of 15–20 mA consumption typically during

device RUN mode, the LV domain consumption IDD(VDD_BV) is thus limited to IDDMAX –

IDD(VDD_HV), i.e., 80 mA.

Therefore, respecting the maximum power allowed as explained in Section 4.5.2: Package

thermal characteristics, it is recommended to use this resistor only in the 125 °C/5.5 V

operating corner as per the following guidelines:



If IDD(VDD_BV) < 80 mA, then no resistor is required.



If 80 mA < IDD(VDD_BV) < 90 mA, then 4  resistor can be used.



If IDD(VDD_BV) > 90 mA, then 8  resistor can be used.

Using resistance in the range of 4–8

, the gain will be around 10–20% of total consumption

on VDD_BV. For example, if 8  resistor is used, then power consumption when IDD(VDD_BV)

is 110 mA is equivalent to power consumption when IDD(VDD_BV) is 90 mA (approximately)

when resistor not used.

In order to ensure correct power up, the minimum VDD_BV to be guaranteed is 30 ms/V. If

the supply ramp is slower than this value, then LVDHV3B monitoring ballast supply VDD_BV

pin gets triggered leading to device reset. Until the supply reaches certain threshold, this low

voltage detector (LVD) generates destructive reset event in the system. This threshold

depends on the maximum IDD(VDD_BV) possible across the external resistor.

4.5.2

Package thermal characteristics

Table 15. LQFP thermal characteristics(1)

Symbol

Parameter

Conditions(2)

Pin count

Value

Unit

Min Typ Max

RJA CC D

Thermal resistance, junction-to-

ambient natural convection(3)

Single-layer board — 1s

100

—

°C/W

144

—

176

—

Four-layer board — 2s2p

100

—

49.7

144

—

48.3

176

—

47.3

LQFP144 bảng dữ liệu(PDF) 61 Page - STMicroelectronics

LQFP144 bảng dữ liệu(HTML) 61 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL