| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
PC87309VLJ bảng dữ liệu(PDF) 58 Page - National Semiconductor (TI) |
|
|
|
|||||||||||||||||||||||||||||
PC87309VLJ bảng dữ liệu(HTML) 58 Page - National Semiconductor (TI) |
|
58 / 192 page ![]() The Floppy Disk Controller (FDC) (Logical Device 0) 58 www.national.com FIGURE 3-5 on page 59 illustrates the track format for each of the formats recognized by the FORMAT TRACK command. Sixth Command Phase Byte - Data Pattern This byte contains the contents of the data field. Execution Phase The system transfers four ID bytes (track number, head number, sector number and bytes-per-sector code) per sec- tor to the Floppy Disk Controller (FDC) in either DMA or non-DMA mode. Section 3.4.2 on page 45 describes these modes. The entire track is formatted. The data block in the data field of each sector is filled with the data pattern byte. Only the first three status bytes in this phase are significant. TABLE 3-11. Typical Gap 3 Values 1. Gap 2 is specified in the command phase of read, write, scan, and verify commands. Although this is the rec- ommended value, the FDC ignores this byte in read, write, scan and verify commands. 2. Gap 3 is the suggested value for use in the FORMAT TRACK command. This is the programmable Gap 3 illustrated in FIGURE 3-5 on page 59. Result Phase 3.7.5 The INVALID Command If an INVALID command (illegal opcode byte in the com- mand phase) is received by the Floppy Disk Controller (FDC), the controller responds with the result phase Status Register 0 (ST0) in the result phase. See Section 3.5.1 on page 48. The controller does not generate an interrupt during this condition. Bits 7 and 6 in the MSR (see Section 3.3.6 on page 43) are both set to 1, indicating to the microprocessor that the controller is in the result phase and the contents of ST0 must be read. Command Phase Execution Phase None. Drive Type and Data Transfer Rate Bytes in Data Field (decimal) Bytes-Per-Sector Code (hex) End of Track (EOT) Sector # (hex) Bytes in Gap 2 1 (hex) Bytes in Gap 3 2 (hex) 256 01 12 0A 0C 256 01 10 20 32 250 Kbps 512 02 08 2A 50 MFM 512 02 09 2A 50 1024 03 04 80 F0 2048 04 02 C8 FF 4096 05 01 C8 FF 500 Kbps 256 010 1A 0E 36 MFM 512 02 0F 1B 54 512 02 12 1B 6C 1024 03 08 35 74 2048 04 04 99 FF 4096 05 02 C8 FF 8192 06 01 C8 FF 76543210 Result Phase Status Register 0 (ST0) Result Phase Status Register 1 (ST1) Result Phase Status Register 2 (ST2) Undefined Undefined Undefined Undefined 76543210 Invalid Opcodes |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |