| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
PIC18F4331 bảng dữ liệu(PDF) 238 Page - Microchip Technology |
|
|
|||||||||||||||||||||||||||||
PIC18F4331 bảng dữ liệu(HTML) 238 Page - Microchip Technology |
|
238 / 396 page ![]() PIC18F2331/2431/4331/4431 DS39616B-page 236 Preliminary 2003 Microchip Technology Inc. 19.3.5 BREAK CHARACTER SEQUENCE The enhanced USART module has the capability of sending the special break character sequences that are required by the LIN bus standard. The break char- acter transmit consists of a Start bit, followed by 12 ‘0’ bits and a Stop bit. The frame break character is sent whenever the SENDB and TXEN bits (TXSTA<3> and TXSTA<5>) are set, while the transmit shift register is loaded with data. Note that the value of data written to TXREG will be ignored and all ‘0’s will be transmitted. The SENDB bit is automatically reset by hardware after the corresponding Stop bit is sent. This allows the user to preload the transmit FIFO with the next transmit byte following the break character (typically, the sync char- acter in the LIN specification). Note that the data value written to the TXREG for the break character is ignored. The write simply serves the purpose of initiating the proper sequence. The TRMT bit indicates when the transmit operation is active or idle, just as it does during normal transmis- sion. See Figure 19-9 for the timing of the break character sequence. 19.3.5.1 Break and Sync Transmit Sequence The following sequence will send a message frame header made up of a break, followed by an auto-baud sync byte. This sequence is typical of a LIN bus master. 1. Configure the USART for the desired mode. 2. Set the TXEN and SENDB bits to setup the break character. 3. Load the TXREG with a dummy character to initiate transmission (the value is ignored). 4. Write ‘55h’ to TXREG to load the Sync character into the transmit FIFO buffer. 5. After the break has been sent, the SENDB bit is reset by hardware. The sync character now transmits in the Pre-Configured mode. When the TXREG becomes empty, as indicated by the TXIF, the next data byte can be written to TXREG. 19.3.6 RECEIVING A BREAK CHARACTER The enhanced USART module can receive a break character in two ways. The first method forces to configure the baud rate at a frequency of 9/13 the typical speed. This allows for the Stop bit transition to be at the correct sampling location (13 bits for break versus Start bit and 8 data bits for typ- ical data). The second method uses the auto-wake-up feature described in Section 19.3.4 “Auto-Wake-up on SYNC BREAK Character”. By enabling this feature, the USART will sample the next two transitions on RX/ DT, cause an RCIF interrupt, and receive the next data byte followed by another interrupt. Note that following a break character, the user will typically want to enable the auto-baud rate detect feature. For both methods, the user can set the ABD bit before placing the USART in its Sleep mode. FIGURE 19-9: SEND BREAK CHARACTER SEQUENCE Write to TXREG Dummy Write BRG Output (Shift Clock) Start Bit Bit 0 Bit 1 Bit 11 Stop Bit Break TXIF bit (Transmit Buffer Reg. Empty Flag) TX (pin) TRMT bit (Transmit Shift Reg. Empty Flag) SENDB (Transmit Shift Reg. Empty Flag) SENDB Sampled Here Auto-Cleared |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |