AM29LV065D datasheet(23/52 Pages) AMD

23 / 52 page

Am29LV065D

January 10, 2002

Table 9.

Primary Vendor-Specific Extended Query

COMMAND DEFINITIONS

Writing specific address and data commands or se-

quences into the command register initiates device op-

erations. Table 10 defines the valid register command

sequences. Writing incorrect address and data val-

ues or writing them in the improper sequence resets

the device to reading array data.

All addresses are latched on the falling edge of WE#

or CE#, whichever happens later. All data is latched on

the rising edge of WE# or CE#, whichever happens

first. Refer to the AC Characteristics section for timing

diagrams.

Reading Array Data

The device is automatically set to reading array data

after device power-up. No commands are required to

retrieve data. The device is ready to read array data

after completing an Embedded Program or Embedded

Erase algorithm.

After the device accepts an Erase Suspend command,

the device enters the erase-suspend-read mode, after

whic h t he s y s t em c an r ead dat a f r om any

non-erase-suspended sector. After completing a pro-

gramming operation in the Erase Suspend mode, the

system may once again read array data with the same

exception. See the Erase Suspend/Erase Resume

Commands section for more information.

The system must issue the reset command to return

the device to the read (or erase-suspend-read) mode

if DQ5 goes high during an active program or erase

operation, or if the device is in the autoselect mode.

See the next section, Reset Command, for more infor-

mation.

Addresses (x8)

Data

Description

40h

41h

42h

50h

52h

49h

Query-unique ASCII string “PRI”

43h

31h

Major version number, ASCII

44h

31h

Minor version number, ASCII

45h

01h

Address Sensitive Unlock (Bits 1-0)

0 = Required, 1 = Not Required

Silicon Revision Number (Bits 7-2)

46h

02h

Erase Suspend

0 = Not Supported, 1 = To Read Only, 2 = To Read & Write

47h

04h

Sector Protect

0 = Not Supported, X = Number of sectors in per group

48h

01h

Sector Temporary Unprotect

00 = Not Supported, 01 = Supported

49h

04h

Sector Protect/Unprotect scheme

04 = 29LV800 mode

4Ah

00h

Simultaneous Operation

00 = Not Supported, X = Number of Sectors in Bank

4Bh

000h

Burst Mode Type

00 = Not Supported, 01 = Supported

4Ch

00h

Page Mode Type

00 = Not Supported

4Dh

B5h

ACC (Acceleration) Supply Minimum

00h = Not Supported, D7-D4: Volt, D3-D0: 100 mV

4Eh

C5h

ACC (Acceleration) Supply Maximum

00h = Not Supported, D7-D4: Volt, D3-D0: 100 mV

4Fh

00h

Top/Bottom Boot Sector Flag

02h = Bottom Boot Device, 03h = Top Boot Device

AM29LV065D bảng dữ liệu(PDF) 23 Page - Advanced Micro Devices

AM29LV065D bảng dữ liệu(HTML) 23 Page - Advanced Micro Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52

bảng dữ liệu tải về

Link URL