PI5C3125LE datasheet(3/6 Pages) PERICOM

3 / 6 page

PI5C3125/3126

4-Bit Bus Switch w/Individual Enables

PS7013F

09/13/04

DC Electrical Characteristics (Over the Operating Range, TA = –40°C to +85°C, VCC = 5V ± 10%)

Parameters

Description

Test Conditions(1)

Min.

Typ(2) Max. Units

VIH

Input HIGH Voltage

Guaranteed Logic HIGH Level

2.0

VIL

Input LOW Voltage

Guaranteed Logic LOW Level

–0.5

0.8

IIH

Input HIGH Current

VCC = Max., VIN = VCC

±1

µA

IIL

Input LOW Current

VCC = Max., VIN = GND

±1

IOZH

High Impedance Output Current

0 ≤ A, B ≤ VCC

±1

VIK

Clamp Diode Voltage

VCC = Min., IIN = –18mA

–0.7

–1.2

IOS

Short Circuit Current(3)

A (B) = 0 V, B (A) = VCC

100

Input Hysteresis at Control Pins

150

RON

Switch On-Resistance(4)

VCC = Min., VIN = 0.0V,

ION = 48mA

Ω

VCC = Min., VIN = 2.4V,

ION = 15mA

VCC = 4V, VIN = 2.4V,

ION = 15mA

Power Supply Characteristics

Parameters

Description

Test Conditions(1)

Min.

Typ(2)

Max.

Units

ICC

Quiescent Power

Supply Current

VCC = Max.

VIN = GND

or VCC

0.1

3.0

µA

ΔICC

Supply Current per

Input @ TTL HIGH

VCC = Max.

VIN = 3.4V(3)

2.5

ICCD

Supply Current per

Input per MHz(4)

VCC = Max.,

A and B Pins Open

BEn/BEn = GND

Control Input Toggling

50% Duty Cycle

0.25

mA/

MHz

Notes:

For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device.

Typical values are at VCC = 5.0V, +25°C ambient.

Per TTL driven input (VIN = 3.4V, control inputs only); A and B pins do not contribute to ICC.

This current applies to the control inputs only and represent the current required to switch internal capacitance at the specified frequency.

The A and B inputs generate no significant AC or DC currents as they transition. This parameter is not tested, but is guaranteed by design.

Capacitance (TA = 25°C, f = 1 MHz)

Parameters(5)

Description

Test Conditions

Typ.

Max.

Units

CIN

Input Capacitance

VIN = 0V

COFF

A/B Capacitance, Switch Off

CON

A/B Capacitance, Switch On

Notes:

For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type.

Typical values are at VCC = 5.0V, TA = 25°C ambient and maximum loading.

Not more than one output should be shorted at one time. Duration of the test should not exceed one second.

Measured by the voltage drop between A and B pin at indicated current through the switch. ON resistance is determined by the lower of the

voltages on the two (A, B) pins.

This parameter is determined by device characterization but is not production tested.

PI5C3125LE bảng dữ liệu(PDF) 3 Page - Pericom Semiconductor Corporation

PI5C3125LE bảng dữ liệu(HTML) 3 Page - Pericom Semiconductor Corporation

Html Pages

1 2 3 4 5 6

bảng dữ liệu tải về

Link URL