| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
IRPLDIM1 bảng dữ liệu(PDF) 7 Page - International Rectifier |
|
|
|||||||||||||||||||||||||||||
IRPLDIM1 bảng dữ liệu(HTML) 7 Page - International Rectifier |
|
7 / 12 page ![]() 7 www.irf.com Ballast Design Lamp Requirements Before selecting component values for the bal- last output stage and the programmable inputs of the IR21592, the following lamp requirements must first be defined: Table I, Typical lamp requirements Ballast Output Stage The components comprising the output stage are selected using a set of equations. Different ballast operating frequencies and their respec- tive voltages and currents are calculated. The inductor and capacitor values are obtained us- ing equations (2) through (7). The results of these equations reveal the location of each operating frequency and the corresponding volt- ages and currents. For a given L, C, DC bus voltage, and pre-heat current, the resulting volt- age over the lamp during pre-heat is given as: π π DC ph DC ph V I C L V V − + = 2 2 8 [Vpp] (2) The resulting operating frequency during pre- heat is given as: ph ph ph CV I f π 2 = [Hz] (3) The resulting operating frequency during igni- tion is given as: LC V V f ign DC ign π π 4 1 2 1 + = [Hz] (4) The total load current during ignition is given as: If CV ign ign ign = 2 π [App] (5) The operating frequency [Hz] at maximum lamp power is given as: (6) The cathode heating current at minimum lamp power is given as: 2 % 1 % 1 % 1 C f V I Cath π = (7) Design Constraints The inductor and capacitor values should be it- erated until the following design constraints have been fulfilled (Table II). Table II, Ballast design constraints 2 2 2 % 100 2 4 % 100 2 2 % 100 4 % 100 2 2 % 100 % 100 4 1 4 32 1 32 1 2 1 C L V V V C P LC V C P LC f DC − − − + − = π π Variable Description Units ph I Filament pre-heat current Arms ph t Filament pre-heat time s max ph V Maximum lamp pre-heat voltage Vpp ign V Lamp ignition voltage Vpp % 100 P Lamp power at 100% brightness W % 100 V Lamp voltage at 100% brightness Vpp % 1 P Lamp power at 1% brightness W % 1 V Lamp voltage at 1% brightness Vpp min Cath I Minimum cathode heating current Arms Design Constraint Reason VV ph ph < max Ignition during pre-heat ff kHz ph ign −> 5 Production tolerances II ign ign < max Inductor saturation min % 1 Cath Cath I I ≥ Lamp extinguishing during dimming |
|
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |