LM4120 datasheet(5/11 Pages) NSC

5 / 11 page

Electrical Characteristics

LM4120-3.0V, 3.3V, 4.096V and 5.0V Unless otherwise specified V

IN = VOUT + 1V, ILOAD = 0, COUT =

0.01µF, T

A = Tj = 25˚C. Limits with standard typeface are for Tj = 25˚C, and limits in boldface type apply over the −40˚C ≤

≤ +85˚C temperature range. (Continued)

Symbol

Parameter

Conditions

Min (Note 5)

Typ (Note 4)

Max (Note 5)

Units

Logic High Input Voltage

2.4

Logic Low Input Voltage

0.4

0.2

Logic High Input Current

µA

Logic Low Input Current

0.1

µA

Short Circuit Current

OUT = 015

630

IN = 12V, VOUT = 017

630

Hyst

Thermal Hysteresis

(Note 7)

−40˚C

≤ T

A ≤ 125˚C

0.5

mV/V

∆V

OUT

Long Term Stability

(Note 9)

1000 hrs. @ 25˚C

100

ppm

Note 1: “Absolute Maximum Ratings” indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is

intended to be functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see Electrical Characteristics. The guar-

anteed specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test

conditions.

Note 2: Without PCB copper enhancements. The maximum power dissipation must be de-rated at elevated temperatures and is limited by TJMAX (maximum junction

temperature),

θJ-A (junction to ambient thermal resistance) and TA (ambient temperature). The maximum power dissipation at any temperature is: PDissMAX = (TJMAX

−TA)/θJ-A up to the value listed in the Absolute Maximum Ratings.

Note 3: The human body model is a 100 pF capacitor discharged through a 1.5 k

Ω resistor into each pin. The machine model is a 200 pF capacitor discharged di-

rectly into each pin.

Note 4: Typical numbers are at 25˚C and represent the most likely parametric norm.

Note 5: Limits are 100% production tested at 25˚C. Limits over the operating temperature range are guaranteed through correlation using Statistical Quality Control

(SQC) methods. The limits are used to calculate National’s Averaging Outgoing Quality Level (AOQL).

Note 6: Dropout voltage is the differential voltage between VOUT and VIN at which VOUT changes ≤ 1% from VOUT at VIN = 3.3V for 1.8V, 2.0V, 2.5V and VOUT +

1V for others.For 1.8V option, dropout voltage is not guaranteed over temperature. A parasitic diode exists between input and output pins; it will conduct if VOUT is

pulled to a higher voltage than VIN.

Note 7: Thermal hysteresis is defined as the change in +25˚C output voltage before and after exposing the device to temperature extremes.

Note 8: Output noise voltage is proportional to VOUT.VN for other voltage option is calculated using (VN(1.8V)/1.8) * VOUT.VN (2.5V) = (36µVPP/1.8) * 2.5 = 46µVPP.

Note 9: Long term stability is change in VREF at 25˚C measured continuously during 1000 hrs.

LM4120 Typical Operating Characteristics Unless otherwise specified, V

IN = 3.3V, VOUT = 2.5V,

LOAD = 0, COUT = 0.022µF, TA = 25˚C and VEN = VIN.

Long Term Drift

DS101047-12

Typical Temperature Drift

DS101047-13

Short Circuit Current vs

Temperature

DS101047-14

LM4120 bảng dữ liệu(PDF) 5 Page - National Semiconductor (TI)

LM4120 bảng dữ liệu(HTML) 5 Page - National Semiconductor (TI)

Html Pages

1 2 3 4 5 6 7 8 9 10 11

bảng dữ liệu tải về

Link URL