| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
KSZ9031RNXVC bảng dữ liệu(PDF) 39 Page - Microchip Technology |
|
|
|||||||||||||||||||||||||||||
KSZ9031RNXVC bảng dữ liệu(HTML) 39 Page - Microchip Technology |
|
39 / 78 page ![]() 2016 Microchip Technology Inc. DS00002117C-page 39 KSZ9031RNX Note 4-1 RW = Read/Write; RO = Read Only; SC = Self-Cleared; LH = Latch High; LL = Latch Low. D.4:0 MMD – Device Address These five bits set the MMD device address. RW 0_0000 Register Eh - MMD Access – Register/Data E.15:0 MMD – Register/ Data For the selected MMD device address (Reg. Dh, Bits [4:0]), When Reg. Dh, Bits [15:14] = 00, this register contains the read/write register address for the MMD device address. Otherwise, this register contains the read/write data value for the MMD device address and its selected register address. See also Reg. Dh, Bits [15:14], for descriptions of post increment reads and writes of this register for data operation. RW 0000_0000_0000_00 00 Register Fh – Extended Status F.15 1000BASE-X Full-Duplex 1 = PHY can perform 1000BASE-X full-duplex 0 = PHY cannot perform 1000BASE-X full-duplex RO 0 F.14 1000BASE-X Half-Duplex 1 = PHY can perform 1000BASE-X half-duplex 0 = PHY cannot perform 1000BASE-X half-duplex RO 0 F.13 1000BASE-T Full-Duplex 1 = PHY can perform 1000BASE-T full-duplex 0 = PHY cannot perform 1000BASE-T full-duplex RO 1 F.12 1000BASE-T Half-Duplex 1 = PHY can perform 1000BASE-T half-duplex 0 = PHY cannot perform 1000BASE-T half-duplex RO 1 F.11:0 Reserved Ignore when read RO — TABLE 4-4: VENDOR-SPECIFIC REGISTER DESCRIPTIONS Address Name Description Mode Note 4-1 Default Register 11h – Remote Loopback 11.15:9 Reserved Reserved RW 0000_000 11.8 Remote Loopback 1 = Enable remote loopback 0 = Disable remote loopback RW 0 11.7:1 Reserved Reserved RW 1111_010 11.0 Reserved Reserved RO 0 Register 12h – LinkMD – Cable Diagnostic 12.15 Cable Diagnostic Test Enable Write value: 1 = Enable cable diagnostic test. After test has completed, this bit is self-cleared. 0 = Disable cable diagnostic test. Read value: 1 = Cable diagnostic test is in progress. 0 = Indicates cable diagnostic test (if enabled) has completed and the status information is valid for read. RW/SC 0 12.14 Reserved This bit should always be set to ‘0’. RW 0 TABLE 4-3: IEEE-DEFINED REGISTER DESCRIPTIONS (CONTINUED) Address Name Description Mode Note 4-1 Default |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |