SIW1711FIF datasheet(5/10 Pages) RFMD

5 / 10 page

5 of 12

SiW1711

60 0047 R00Grf SiW1711 Radio Modem IC DS

Digital Regulator Specification (TOP = 25°C)

Internal Analog Voltage Regulator Specification (TOP=+25°C, VBATT_ANA = 3.3 V)

Radio Specification

RF Impedances

Receiver Specification1

(VBATT_ANA, VBATT_DIG=3.3V, VCC=int. analog reg. output, and nominal2 Bluetooth test conditions)

Parameter

Description

Min

Typ

Max

Unit

Output voltage

(I OUT = 10 mA)

1.55

1.85

2.16

Line regulation

(I OUT = 0 mA, VBATT_DIG = 2.3 V to 3.63 V)

–

8.0

–

Load regulation

(I OUT = 3 mA to 80 mA)

–

9.0

–

Dropout voltage

(I OUT = 10 mA)

–

250

Output maximum current

–

Quiescent current

–

µA

Ripple rejection

f RIPPLE = 400 Hz

–40

–

Parameter

Description

Min

Typ

Max

Unit

Output voltage (40 mA load)

–

1.71

1.80

1.89

Ripple rejection

–

Parameter

Description

Min

Typ

Max

Unit

VCO operating range

Frequency

2402

–

2480

MHz

PLL lock time

–

100

µs

Parameter1

Description

Min

Typ

Max

Unit

RF impedance

TX On

–

448//0.6

–

Ω/pF

TX Off

–

53.1//2.2

–

Ω/pF

RX On

–

267//1.1

–

Ω/pF

RX Off

–

23.4//0

–

Ω/pF

1The impedance values are for typical samples in 32-pin QFN package.

Parameter

Description

Min

Typ

Max

Unit

Receiver

sensitivity

BER<0.1%

–

-85.0

-80.0

dBm

Maximum usable signal

BER<0.1%

-10

–

dBm

C/I co-channel

(0.1% BER)

Co-channel selectivity

–

8.0

11.0

C/I 1MHz

(0.1% BER)

Adjacent channel selectivity

–

-4.0

C/I 2MHz

(0.1% BER)

2nd adjacent channel selectivity

–

-38.0

-35.0

C/I

≥3MHz

(0.1% BER)

3rd adjacent channel selectivity

–

-43

-40

Out-of-band

blocking3

30MHz to 2000MHz

-10

–

dBm

2000MHz to 2399MHz

-27

–

dBm

2498MHz to 3000MHz

-27

–

dBm

3000MHz to 12.75GHz

-10

–

dBm

Intermodulation

Max interferer level to maintain 0.1% BER,

interference signals at 3 MHz and 6 MHz offset.

-39

-36

–

dBm

Receiver spurious

emission

30MHz to 1GHz

–

-57

dBm

1 GHz to 12.75 GHz

–

-47

dBm

1Measured with a proper matching circuit without bandpass filter.

2Nominal and extreme Bluetooth test conditions as defined by the Bluetooth Test and Interoperability Working Group published RF Test

Specification 1.1.

3Out-of-band blocking guaranteed by design.

SIW1711FIF bảng dữ liệu(PDF) 5 Page - RF Micro Devices

SIW1711FIF bảng dữ liệu(HTML) 5 Page - RF Micro Devices

Html Pages

1 2 3 4 5 6 7 8 9 10

bảng dữ liệu tải về

Link URL